YASKAWA NX100 - Page 21

Table of Contents
xxi
149235-1CD
RE-CSO-A031
 RS033: TRANSMISSION SPEED. . . . . . . . . . . . . . . . . . . .8-50
 RS034: RESPONSE WAITING TIMER (TIMER A). . . . . . .8-50
 RS035: TEXT TERMINATION MONITORING TIMER
(TIMER B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-50
 RS036: NUMBER OF ENQ RE-TRANSMISSION
RETRIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-50
 RS037: NUMBER OF DATA RE-TRANSMISSION
RETRIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-50
 RS038: BLOCK CHECK METHOD . . . . . . . . . . . . . . . . . . .8-50
8.9.2 FC1 Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-51
 RS050: NUMBER OF DATA BITS . . . . . . . . . . . . . . . . . . .8-51
 RS051: NUMBER OF STOP BITS . . . . . . . . . . . . . . . . . . .8-51
 RS052: PARITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-51
 RS053: TRANSMISSION SPEED. . . . . . . . . . . . . . . . . . . .8-51
 RS054: RESPONSE WAITING TIMER (TIMER A). . . . . . .8-51
 RS055: TEXT TERMINATION MONITORING TIMER
(TIMER B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-51
 RS056: NUMBER OF ENQ RE-TRANSMISSION
RETRIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-51
 RS057: NUMBER OF DATA RE-TRANSMISSION
RETRIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-51
 RS058: FC2 FORMAT SPECIFICATION . . . . . . . . . . . . . .8-51
 RS059: EXTERNAL MEMORY FILE OVERWRITE
SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-51
8.10 Application Parameters . . . . . . . . . . . . . . . . . . . . . . . . . 8-52
8.10.1 Arc Welding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-52
 AxP000: APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . .8-52
 AxP003: WELDING ASSIGNMENT OF WELDING
START CONDITION FILE. . . . . . . . . . . . . . . . . . . . . . . . . .8-52
 AxP004: WELDING ASSIGNMENT OF WELDING END
CONDITION FILES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-52
 AxP005: WELDING SPEED PRIORITY . . . . . . . . . . . . . . .8-52
 AxP009: WORK CONTINUING. . . . . . . . . . . . . . . . . . . . . .8-52
 AxP010: WELDING INSTRUCTION OUTPUT . . . . . . . . . .8-52
 AxP011, AxP012: MANUAL WIRE OPERATION SPEED. .8-53
 AxP013, AxP014: WELDING CONTROL TIME . . . . . . . . .8-53
 AxP015 to AxP017: NUMBER OF WELDING CONTROL .8-53
 AxP026 to AxP029: TOOL ON/OFF USER OUTPUT NO.
(Jigless system). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-53
8.10.2 Handling Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-53
 AxP002, AxP004: f1 KEY FUNCTION . . . . . . . . . . . . . . . .8-53
 AxP003, AxP005: f2 KEY FUNCTION . . . . . . . . . . . . . . . .8-53
8.10.3 Spot Welding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-53
 AxP003: MAXIMUM NUMBERS OF CONNECTED
POWER SOURCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-53
 AxP004: GUN FULL OPEN STROKE ON/OFF SIGNAL . .8-53
 AxP005: STROKE CHANGE ANSWER TIME LIMIT . . . . .8-54
 AxP006: PARITY SPECIFICATION FOR WELDING
CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-54
 AxP007: ANTICIPATE TIME . . . . . . . . . . . . . . . . . . . . . . . .8-54
 AxP015: WELDING ERROR RESET OUTPUT TIME. . . . .8-54
21 of 493