Siemens SCALANCE W1750D CLI - Page 277

CLI Commands
4.16 S
SCALANCE W1750D CLI
Function Manual, 03/2019, C79000-G8976-C452-04
277
2013-05-10
10:33:07
157+
149+
27
27
I
2013-05-10
10:25:35
149+
157+
27
27
I
2013-05-10
09:18:11
157+
149+
27
27
I
2013-05-10
09:04:24
149+
157+
27
27
I
2013-05-10
06:08:59
157+
149+
27
27
I
2013-05-10
05:55:10
153-
157+
27
27
I
2013-05-10
05:11:21
157+
153-
27
27
I
Interface :wifi1
ARM History
-----------
Time of Change Old Channel New Channel Old Power New Power Reason
-------------- ----------- ----------- --------- --------- ------
2013-05-11
04:16:28
6 1 24 24 I
2013-05-11
03:58:53
11 6 24 24 I
2013-05-11
03:13:44
1 11 24 24 I
2013-05-11
01:23:32
6 1 24 24 I
2013-05-11
01:04:29
11 6 24 24 I
2013-05-11
00:26:16
1 11 24 24 I
2013-05-10
23:13:30
6 1 24 24 I
2013-05-10
23:04:49
11 6 24 24 Q
2013-05-10
22:51:10
6 11 24 24 I
2013-05-10
22:45:01
1 6 24 24 I
2013-05-10
21:52:39
6 1 24 24 I
2013-05-10
21:44:37
1 6 24 24 Q
2013-05-10
21:29:52
6 1 24 24 I
2013-05-10
21:19:16
11 6 24 24 I
2013-05-10
21:12:53
6 11 24 24 I
2013-05-10
20:52:07
1 6 24 24 I
2013-05-10
19:28:09
6 1 24 24 I
2013-05-10
19:02:08
11 6 24 24 I
2013-05-10
18:23:32
1 11 24 24 I
2013-05-10
17:40:55
6 1 24 24 I
2013-05-10
17:28:40
11 6 24 24 I
2013-05-10
17:01:24
1 11 24 24 I
2013-05-10
15:10:19
6 1 24 24 I
2013-05-10
15:03:41
11 6 24 24 I
2013-05-10
14:45:39
6 11 24 24 I
2013-05-10
14:19:32
11 6 24 24 I
2013-05-10
13:37:30
1 11 24 24 I
2013-05-10
11:34:27
6 1 24 24 I
2013-05-10
11:19:52
11 6 24 24 I
2013-05-10
10:30:51
1 11 24 24 I
2013-05-10
09:18:51
6 1 24 24 I
2013-05-10
09:06:31
11 6 24 24 I
I: Interference, R: Radar detection, N: Noise exceeded, Q: Bad Channel Quality E:
Error threshold exceeded, INV: Invalid Channel, G: Rogue AP Containment, M: Empty
Channel, P+: Increase Power, P-: Decrease Power, 40INT: 40MHZ intol detected on 2.4G,
NO40INT: 40MHz intol cleared on 2.4G, OFF: Turn off Radio, ON: Turn on Radio
Column
Description
Time of change
Indicates the timestamp of the channel changes for each interface.
Old Channel
Displays the channel number used by the AP before the ARM change.
New channel
Displays the channel number used by the AP after the ARM change.
Old Power
Indicates power values configured on the AP before the ARM change.