Rohde & Schwarz SMW200A - Instrument Name; RF Couple

Signal Routing and System Configuration
R&S
®
SMW200A
153User Manual 1175.6632.02 ─ 16
To connect/disconnect all external instruments, use the functions Connect/Disconnect
All Remote.
Note:
External instruments connected to the R&S SMW are preset (:DEVice:PRESet)
whenever:
●
The connection to the external instrument is established or terminated ("Connect/
Disconnect All Remote" or "Rem. Conn > On/Off")
●
The R&S SMW is preset (PRESET).
Note: An active "Rem. Conn." and an "RF State > On" do not mean that an I/Q stream
is mapped to this connector.
Use the "System Configuration > External Rf and I/Q > Display > Mapped Connectors"
filter to list only the connectors with a mapped I/Q stream.
Remote command:
:SCONfiguration:EXTernal:CODer<ch>:RCONnection:STATe? on page 846
:SCONfiguration:EXTernal:CODer<ch>:REMote:DISConnect on page 852
:SCONfiguration:EXTernal:FADer<ch>:RCONnection:STATe? on page 846
:SCONfiguration:EXTernal:FADer<ch>:REMote:DISConnect on page 852
:SCONfiguration:EXTernal:BBMM<ch>:RCONnection:STATe? on page 846
:SCONfiguration:EXTernal:BBMM<ch>:REMote:DISConnect on page 852
:SCONfiguration:EXTernal:IQOutput<ch>:RCONnection:STATe?
on page 846
:SCONfiguration:EXTernal:IQOutput<ch>:REMote:DISConnect
on page 852
:SCONfiguration:EXTernal:CODer<ch>:REMote:INFO? on page 852
:SCONfiguration:EXTernal:FADer<ch>:REMote:INFO? on page 852
:SCONfiguration:EXTernal:BBMM<ch>:REMote:INFO? on page 852
:SCONfiguration:EXTernal:IQOutput<ch>:REMote:INFO? on page 852
Instrument Name
Displays useful information on the connected external instrument, like the instrument
designation and the RF path the RF settings are coupled to.
Remote command:
:SCONfiguration:EXTernal:CODer<ch>:INAMe? on page 846
:SCONfiguration:EXTernal:FADer<ch>:INAMe? on page 846
:SCONfiguration:EXTernal:BBMM<ch>:INAMe? on page 846
:SCONfiguration:EXTernal:IQOutput<ch>:INAMe? on page 846
:SCONfiguration:EXTernal:CODer<ch>:REMote:INFO? on page 852
:SCONfiguration:EXTernal:FADer<ch>:REMote:INFO? on page 852
:SCONfiguration:EXTernal:BBMM<ch>:REMote:INFO? on page 852
:SCONfiguration:EXTernal:IQOutput<ch>:REMote:INFO? on page 852
RF Couple
If enabled, this parameter couples all major RF setting (like the "RF Frequency", the
"RF Level" and the "RF State") of the external instrument to the R&S SMW.
The R&S SMW acts as a "master", i.e the external instruments synchronize their set-
tings and the RF A output state to the R&S SMW. You can apply delta frequency and
level offset to the signal.
System Configuration Settings