TP-Link T2600G Series User Manual

Configuring Access Security Access Security Configurations
User Guide
707
Step 2 ■ Use the following command to control the users’ access by limiting the IP address:
user access-control ip-based enable
Configure the control mode as IP-based.
user access-control ip-based {
ip-addr ip-mask } [ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [
ping ] [ all ]
Only the users within a certain IP-range can access the switch via the specified interfaces.
ip-addr : Specify the IP address of the user.
ip-mask : Specify the subnet mask of the user.
[ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ]: Select the interfaces where to apply the
Access Control rule. If an interface is unselected, all users can access the switch via it. By
default, all the interfaces are selected.
■ Use the following command to control the users’ access by limiting the MAC address:
user access-control mac-based enable
Configure the control mode as MAC-based.
user access-control mac-based {
mac-addr } [ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [
all ]
Only the users with a certain MAC address can access the switch via the specified interfaces.
mac-addr : Specify the MAC address of the user.
[ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ]: Select the interfaces where to apply the
Access Control rule. If an interface is unselected, all users can access the switch via it. By
default, all the interfaces are selected.
■ Use the following command to control the users’ access by limiting the ports connected to
the users:
user access-control port-based enable
Configure the control mode as Port-based.
user access-control port-based interface { fastEthernet
port-list | gigabitEthernet port-list
| ten-gigabitEthernet
port-list } [ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ]
Only the users who are connected to certain ports can access the switch via the specified
interfaces.
port-list : Specify the list of Ethernet port, in the format of 1/0/1-4. You can appoint 5 ports at
most.
[ snmp ] [ telnet ] [ ssh ] [ http ] [ https ] [ ping ] [ all ]: Select the interfaces where to apply the
Access Control rule. If an interface is unselected, all users can access the switch via it. By
default, all the interfaces are selected.
Step 3 show user configuration
Verify the security configuration information of the user authentication information and the
access interface.
Step 4 end
Return to privileged EXEC mode.

TP-Link T2600G Series Specifications

General

Model	T2600G Series
Layer	Layer 2+
Type	Managed
Uplink Ports	4 x Gigabit SFP slots
VLAN	4K VLANs
QoS	8 priority queues
Management	Web-based GUI, CLI, SNMP, RMON
Standards and Protocols	IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3ad, IEEE 802.3x, IEEE 802.1d, IEEE 802.1s, IEEE 802.1w, IEEE 802.1q, IEEE 802.1p, IEEE 802.3af, IEEE 802.3at
Interface	RJ45
L2 Features	STP, RSTP, MSTP, LACP, IGMP Snooping
L3 Features	Static Routing
Security	802.1X, Port Security, DHCP Snooping, IP Source Guard, DoS Defend, ARP Inspection, SSH, SSL, ACL
MAC Address Table	16K
Jumbo Frame	9KB
Operating Temperature	0°C to 40°C
Storage Temperature	-40°C to 70°C
Operating Humidity	10% to 90% RH non-condensing
Storage Humidity	5% to 90% non-condensing