EasyManuals Logo

TP-Link T2600G Series User Manual

TP-Link T2600G Series
1136 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #758 background imageLoading...
Page #758 background image
Configuring AAA AAA Configuration
User Guide
729
Step 5 copy running-config startup-config
Save the settings in the configuration file.
The following example shows how to add a RADIUS server on the switch. Set the IP address
of the server as 192.168.0.10, the authentication port as 1812, the shared key as 123456,
the timeout as 8 seconds and the retransmit number as 3.
Switch#configure
Switch(config)#radius-server host 192.168.0.10 auth-port 1812 timeout 8 retransmit 3
key 123456
Switch(config)#show radius-server
Server Ip Auth Port Acct Port Timeout Retransmit NAS Identifier
Shared key
192.168.0.10 1812 1813 5 2 000AEB132397 123456
Switch(config)#end
Switch#copy running-config startup-config
Adding TACACS+ Server
Follow these steps to add TACACS+ server on the switch:
Step 1 configure
Enter global configuration mode.
Step 2 tacacs-server host
ip-address
[ port
port-id
] [ timeout
time
] [ key { [ 0 ]
string
| 7
encrypted-string
} ]
Add the RADIUS server and configure the related parameters as needed.
host
ip-address
:
Enter the IP address of the server running the TACACS+ protocol.
port
port-id
:
Specify the TCP destination port on the TACACS+ server for authentication
requests. The default setting is 49.
timeout
time
:
Specify the time interval that the switch waits for the server to reply before
resending. The valid values are from 1 to 9 seconds and the default setting is 5 seconds.
key { [ 0 ]
string
| 7
encrypted-string
}: Specify the shared key. 0 and 7 represent the
encryption type. 0 indicates that an unencrypted key will follow. 7 indicates that a symmetric
encrypted key with a xed length will follow. By default, the encryption type is 0.
string
is the
shared key for the switch and the server, which contains 31 characters at most.
encrypted-
string
is a symmetric encrypted key with a fixed length, which you can copy from the
conguration le of another switch. The key or encrypted-key you congured here will be
displayed in the encrypted form.
Step 3 show tacacs-server
Verify the configuration of TACACS+ server.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TP-Link T2600G Series and is the answer not in the manual?

TP-Link T2600G Series Specifications

General IconGeneral
ModelT2600G Series
LayerLayer 2+
TypeManaged
Uplink Ports4 x Gigabit SFP slots
VLAN4K VLANs
QoS8 priority queues
ManagementWeb-based GUI, CLI, SNMP, RMON
Standards and ProtocolsIEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3ad, IEEE 802.3x, IEEE 802.1d, IEEE 802.1s, IEEE 802.1w, IEEE 802.1q, IEEE 802.1p, IEEE 802.3af, IEEE 802.3at
InterfaceRJ45
L2 FeaturesSTP, RSTP, MSTP, LACP, IGMP Snooping
L3 FeaturesStatic Routing
Security802.1X, Port Security, DHCP Snooping, IP Source Guard, DoS Defend, ARP Inspection, SSH, SSL, ACL
MAC Address Table16K
Jumbo Frame9KB
Operating Temperature0°C to 40°C
Storage Temperature-40°C to 70°C
Operating Humidity10% to 90% RH non-condensing
Storage Humidity5% to 90% non-condensing

Related product manuals