Table of Contents
xxiv
155507-1CD
RE-CSO-A037
DX100
8.2.0.16 S2C422: OPERATION AFTER RESET FROM PATH DEVIATION ...... 8-7
8.2.0.17 S2C423: OPERATION AFTER JOB...................................................... 8-7
8.2.0.18 S2C424: DEVIATED POSITION ........................................................... 8-8
8.2.0.19 S2C425: CIRCULAR INTERPOLATION TOOL POSITION CONTROL 8-9
8.2.0.20 S2C653: EMERGENCY STOP CURSOR ADVANCE
CONTROL FUNCTION ......................................................................... 8-9
8.2.0.21 S2C654: EMERGENCY STOP CURSOR ADVANCE CONTROL
FUNCTION CONT PROCESS COMPLETION POSITION ................. 8-10
8.2.0.22 S2C655: EMERGENCY STOP ADVANCE CONTROL FUNCTION
WORK START INSTRUCTION STEP MOTION COMPLETION
DELAY TIME .......................................................................................8-10
8.2.0.23 S2C698: BASE AXIS OPERATION KEY ALLOCATION SETTING .... 8-10
8.2.0.24 S3C1098 to S3C1102: POSITION CORRECTING FUNCTION
DURING PLAYBACK .......................................................................... 8-11
8.3 Mode Operation Setting Parameters ............................................................................... 8-12
8.3.0.1 S2C195: SECURITY MODE WHEN CONTROL POWER SUPPLY
IS TURNED ON..................................................................................... 8-12
8.3.0.2 S2C196: SELECTION OF CARTESIAN/CYLINDRICAL....................... 8-12
8.3.0.3 S2C197: COORDINATE SWITCHING PROHIBITED ........................... 8-12
8.3.0.4 S2C198: EXECUTION UNITS AT “FORWARD” OPERATION .............8-12
8.3.0.5 S2C199: INSTRUCTION (EXCEPT FOR MOVE) EXECUTION AT
“FORWARD” OPERATION ................................................................... 8-13
8.3.0.6 S2C203: CHANGING STEP ONLY ....................................................... 8-13
8.3.0.7 S2C204: MANUAL SPEED STORING FOR EACH COORDINATE ..... 8-13
8.3.0.8 S2C206: ADDITIONAL STEP POSITION ............................................. 8-13
8.3.0.9 S2C207: MASTER JOB CHANGING OPERATION.............................. 8-14
8.3.0.10 S2C208: CHECK AND MACHINE-LOCK KEY OPERATION IN
PLAY MODE........................................................................................ 8-14
8.3.0.11 S2C209: RESERVED WORK JOB CHANGING OPERATION ........... 8-14
8.3.0.12 S2C210: MASTER OR SUBMASTER CALL OPERATION IN
PLAY MODE........................................................................................ 8-15
8.3.0.13 S2C211: LANGUAGE LEVEL ............................................................. 8-16
8.3.0.14 S2C214: INSTRUCTION INPUT LEARNING FUNCTION .................. 8-16
8.3.0.15 S2C215: ADDRESS SETTING WHEN CONTROL POWER IS
TURNED ON ....................................................................................... 8-16
8.3.0.16 S2C216: JOB LIST DISPLAY METHOD AT JOB SELECTION ..........8-16
8.3.0.17 S2C217: INITIAL OPERATION OF MANIPULATOR .......................... 8-17
8.3.0.18 S2C218: PLAYBACK EXECUTION AT CYCLE MODE “1- STEP” ..... 8-17
8.3.0.19 S2C219: EXTERNAL START.............................................................. 8-17
8.3.0.20 S2C220: PROGRAMMING PENDANT START................................... 8-17
8.3.0.21 S2C221: SPEED DATA INPUT FORM ............................................... 8-18
8.3.0.22 S2C222: RESERVED START .............................................................8-18
8.3.0.23 S2C224: JOB SELECTION AT REMOTE FUNCTION (PLAY MODE)8-18
8.3.0.24 S2C225: EXTERNAL MODE SWITCH................................................ 8-18
8.3.0.25 S2C227: EXTERNAL CYCLE SWITCHING ........................................ 8-18
8.3.0.26 S2C228: PROGRAMMING PENDAN
T CYCLE SWITCHING............. 8-19
8.3.0.27 S2C229: SERVO ON FROM EXTERNAL PP PROHIBITION............. 8-19
8.3.0.28 S2C230: PROGRAMMING PENDANT OPERATION WHEN “IO”
IS SELECTED FOR REMOTE MODE ................................................ 8-19
8.3.0.29 S2C234: STEP REGISTRATION AT TOOL NO. CHANGE ................ 8-20
To Next Page
Loading...
