YASKAWA DX100 - 3 Inspections

Table of Contents
xxvi
155507-1CD
RE-CSO-A037
DX100
8.6.0.3 S2C231: OPERATION METHOD AT FWD/BWD OPERATION 
OR TEST RUN BY INDEPENDENT CONTROL ...................................8-45
8.6.0.4 S2C232: JOB AT CALLING MASTER OF SUBTASK 
BY INDEPENDENT CONTROL ............................................................ 8-46
8.6.0.5 S2C264: STATION AXIS CURRENT VALUE DISPLAY FUNCTION.... 8-46
8.6.0.6 S2C265 to S2C288: STATION AXIS DISPLAYED UNIT ......................8-46
8.6.0.7 S2C420: POSTURE CONTROL OF SYNCHRONIZED 
MANIPULATOR (When Twin Synchronous Function Used) ................. 8-47
8.6.0.8 S2C421: POSTURE CONTROL OF MANIPULATOR IN MULTI-JOB 
(When Twin Synchronous Function Used) ............................................ 8-47
8.6.0.9 S2C687: OPERATION OF JOB WITHOUT CONTROL GROUP 
SPECIFICATION ................................................................................... 8-48
8.6.0.10 S2C688: EXECUTION OF “BWD” OPERATION................................. 8-48
8.6.0.11 S3C1101: MAXIMUM DEVIATION ANGLE OF CURRENT 
STATION POSITION (When Twin Synchronous Function Used) ....... 8-48
8.7 Parameters for Other Functions or Applications .............................................................. 8-49
8.7.0.1 S1CxG049 to S1CxG051: SMALL CIRCLE CUTTING ......................... 8-49
8.7.0.2 S1CxG052 to S1CxG053: SMALL CIRCLE CUTTING 
DIRECTION LIMIT VALUE.................................................................... 8-49
8.7.0.3 S1CxG054 to S1CxG055: SMALL CIRCLE CUTTING 
OVERLAP VALUE................................................................................. 8-49
8.7.0.4 S1CxG063, S1CxG064: PATTERN CUTTING DIMENSION ................ 8-49
8.7.0.5 S1CxG065: MIRROR SHIFT SIGN INVERSION .................................. 8-49
8.7.0.6 S2C430: RELATIVE JOB OPERATION METHOD ............................... 8-49
8.7.0.7 S3C1111 to S3C1190: ANALOG OUTPUT FILTER CONSTANT 
(When analog output corresponding to speed function is used) ........... 8-50
8.7.0.8 S3C1191: CUT WIDTH CORRECTION VALUE (When form cutting 
function is used) ....................................................................................8-50
8.8 Hardware Control Parameters ......................................................................................... 8-51
8.8.0.1 S2C646: ANTICIPATOR FUNCTION.................................................... 8-51
8.8.0.2 S4C327 to S4C390: SETTING OF OPERATING RELAY NO............... 8-52
8.8.0.3 S4C391 to S4C454: OPERATING METHOD OF RELAYS................... 8-52
8.8.0.4 S2C786 to S2C788: COOLING FAN ALARM DETECTION.................. 8-52
8.8.0.5 S2C789 to S2C792: COOLING FAN ALARM 1 OPERATION .............. 8-53
8.8.0.6 S2C793 to S2C796: COOLING FAN ALARM 2 OPERATION .............. 8-53
8.8.0.7 S2C797 to S2C800: COOLING FAN ALARM 3 OPERATION .............. 8-53
8.8.0.8 S2C801 to S2C804: FAN ALARM 1 POWER SOURCE STATUS........ 8-53
8.8.0.9 S2C805 to S2C808: FAN ALARM 2 POWER SOURCE STATUS........ 8-53
8.8.0.10 S2C809 to S2C812: FAN ALARM 3 POWER SOURCE STATUS...... 8-54
8.9 TRANSMISSION PARAMETERS.................................................................................... 8-55
8.10 Application Parameters..................................................................................................8-55
8.10.1 Arc Welding ...................................................................................................... 8-55
8.10.1.1 AxP000: APPLICATION ...................................................................... 8-55
8.10.1.2 AxP003: WELDING ASSIGNMENT OF WELDING START 
CONDITION FILE................................................................................ 8-55
8.10.1.3 AxP004: WELDING ASSIGNMENT OF WELDING END 
CONDITION FILES ............................................................................. 8-55
8.10.1.4 AxP005: WELDING SPEED PRIORITY .............................................. 8-55
8.10.1.5 AxP009: WORK CONTINUING ........................................................... 8-55
26 of 554