Rohde & Schwarz SMW200A - Page 1303

Index
R&S
®
SMW200A
1288User Manual 1175.6632.02 ─ 16
Preset
Factory preset ........................................................... 625
Fading configuration ................................................. 834
Ramp ........................................................................ 284
System configuration ................................................ 834
Preset instrument settings .........................................42, 775
Preview diagram ............................................................. 138
Print
Hard copy ................................................................. 655
Processing time ...............................................................242
Protection
Settings ..................................................................... 687
Setup ........................................................................ 686
Protection level
1 ................................................................................ 686
2 ................................................................................ 686
3, 4, 5 ........................................................................ 686
Adjustments .............................................................. 686
Calibration .................................................................686
Factory only .............................................................. 686
Protection level ......................................................... 688
Service department ...................................................686
Protocol
NRP sensor mapping ................................................542
VXI ............................................................................ 707
PTRansition ...................................................................1206
PULM
Delay .........................................................................516
Double pulse delay ................................................... 516
Double pulse width ................................................... 516
Impedance (pulse input) ........................................... 514
Mode ......................................................................... 515
Output video polarity ................................................. 514
Period ....................................................................... 515
Pulse polarity (input) ................................................. 514
Source ...................................................................... 513
State ......................................................................... 513
Subsystem ................................................................ 881
Threshold (pulse input) ..................................... 514, 673
Transition type .......................................................... 514
Width .........................................................................516
Pulse
Duty cycle ................................................................. 504
Length (PULM) ......................................................... 516
LF signal ................................................................... 500
Period ....................................................................... 504
Width .........................................................................504
Width (PULM) ........................................................... 516
Pulse divider marker ....................................................... 235
Pulse frequency marker .................................................. 235
Pulse generator
Delay .........................................................................516
Output polarity .......................................................... 516
Output state .............................................................. 516
Subsystem .............................................................. 1089
Width .........................................................................516
Pulse modulation .....................................................502, 512
Double pulse delay ................................................... 516
Double pulse width ................................................... 516
Mode ......................................................................... 515
Output video polarity ................................................. 514
Period ....................................................................... 515
Pulse input impedance ............................................. 514
Pulse input threshold ........................................ 514, 673
Pulse polarity (input) ................................................. 514
Repetition frequency ................................................. 515
Source ...................................................................... 513
State ................................................................. 513, 514
Subsystem ................................................................ 881
Trigger mode ............................................................ 516
Purge
List of external RF and I/Q instrument ...................... 156
Q
Q Offset ........................................................................... 408
QR code .......................................................................... 722
QSFP cable
Disconnect .................................................................. 65
Plugin .......................................................................... 65
Quadrature offset
Impairments .............................................................. 412
Quadrature Offset ........................................................... 408
Queries ................................................................1191, 1199
Status ......................................................................1210
Querying
Baseband power levels .............................................588
Question mark ..................................................... 1197, 1199
Questionable status register ......................................... 1209
Quick shift of the baseband signal
How to .......................................................................387
Quotation mark ..............................................................1197
R
R&S DigIConf
Installing ....................................................................218
R&S EX-IQ-BOX
Connect .................................................................... 219
Set up ....................................................................... 218
Rack
Mounting ..................................................................... 40
Rack installation ................................................................ 62
Raised cosine filter
see Cosine filter ........................................................ 297
Ramp
All up or all down ...................................................... 284
Low to high and vice versa ....................................... 284
Ramp function ................................................................. 279
Ramp time ....................................................................... 279
Ratio
AM ............................................................................ 507
Amplitude modulation ............................................... 507
FM .............................................................................508
Frequency modulation .............................................. 508
Phase modulation ..................................................... 509
PhiM ..........................................................................509
Ratio noise/system bandwidth
Minimum ................................................................... 397
Readjust
ALC ................................................................... 437, 438
Automatic level control ......................................437, 438
Ready state ....................................................................... 41
Recall
Instrument settings ................................................... 632
Recall instrument settings ....................................... 772, 786
Recall intermediate ................................................. 632, 772
Recommendations
remote control programming ...................................1212
Recording ...................................................................... 1224
Rect test signal ................................................................301
Rectangular test signals
Settings ..................................................................... 312