Cisco Catalyst 4500 Series - Operational Uptime

71-4
Catalyst 4500 Series Switch, Cisco IOS Software Configuration Guide - Cisco IOS XE 3.9.xE and IOS 15.2(5)Ex
Chapter 71 Onboard Failure Logging (OBFL)
Information About OBFL
32 209h 935h 138h 0m 120m 141h 258h
33 331h 934h 192m 0m 0m 113h 316h
34 579h 8y 190m 0m 0m 182m 432h
35 17y 149h 80m 0m 0m 150m 8y
36 914h 20m 0m 0m 0m 10m 8y
37 838h 270m 0m 140h 26m 0m 8y
38 47d 0m 0m 102h 108m 0m 790h
39 8y 0m 0m 948m 20m 0m 421h
--------------------------------------
Temp Sensor ID
0C 1 2 3 4 5 6 7
--------------------------------------
40 414h 0m 2m 100m 78h 0m 288h
41 74h 0m 113h 40m 340h 134m 113h
42 10m 0m 380h 0m 198h 0m 446m
43 270m 0m 8y 0m 373h 0m 0m
44 0m 0m 8y 0m 683h 45h 10m
45 0m 0m 8y 2m 17y 274h 0m
46 0m 0m 897h 105m 64d 257h 0m
47 0m 0m 785h 27m 8y 169h 0m
48 0m 0m 639h 4m 319h 666h 0m
49 0m 0m 379h 92h 786m 17y 0m
50 0m 0m 94h 330h 270m 61d 0m
51 0m 0m 106m 192h 0m 48d 0m
52 0m 0m 0m 190h 0m 8y 0m
53 0m 0m 0m 573h 0m 227h 0m
54 0m 0m 0m 736h 0m 180m 0m
55 0m 0m 0m 716h 0m 260m 0m
56 0m 0m 0m 902h 0m 0m 0m
57 0m 0m 0m 8y 0m 0m 0m
58 0m 0m 0m 8y 0m 0m 0m
59 0m 0m 0m 8y 0m 0m 0m
60 0m 0m 0m 226h 0m 0m 0m
61 0m 0m 0m 629m 0m 0m 0m
Switch#
To interpret this data:
• Number of sensors is the total number of temperature sensors that will be recorded. A column for
each sensor is displayed with temperatures listed under the number of each sensor, as available.
• Sampling frequency is the time between measurements.
• Maximum time of storage determines the maximum amount of time, in minutes, that can pass when
the temperature remains unchanged and the data is not saved to storage media. After this time, a
temperature record will be saved even if the temperature has not changed.
• The Sensor column lists the name of the sensor.
• The ID column lists an assigned identifier for the sensor.
• Maximum Temperature 0C shows the highest recorded temperature per sensor.
• Temp indicates a recorded temperature in degrees Celsius in the historical record. Columns
following show the total time each sensor has recorded that temperature.
• Sensor ID is an assigned number, so that temperatures for the same sensor can be stored together.
Operational Uptime
The operational uptime tracking begins when the module is powered on, and information is retained for
the life of the module.