EasyManuals Logo

Cisco Catalyst 4500 Series Software Configuration Guide

Cisco Catalyst 4500 Series
2086 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1951 background imageLoading...
Page #1951 background image
78-7
Catalyst 4500 Series Switch, Cisco IOS Software Configuration Guide - Cisco IOS XE 3.9.xE and IOS 15.2(5)Ex
Chapter 78 Configuring Cisco IOS IP SLA Operations
Configuring IP SLAs Operations
IP SLA Configuration Guidelines
For information on the IP SLAs commands, see the Cisco IOS IP SLAs Command Reference,
Release 12.4T command reference:
http://www.cisco.com/en/US/docs/ios/ipsla/command/reference/sla_book.html
For detailed descriptions and configuration procedures, see the Cisco IOS IP SLAs Configuration Guide,
Release 12.4T L:
http://www.cisco.com/en/US/products/ps6441/products_installation_and_configuration_guides_list.ht
ml
Note that not all of the IP SLAs commands or operations described in this guide are supported on the
switch. The switch supports IP service level analysis by using UDP jitter, UDP echo, HTTP, TCP
connect, ICMP echo, ICMP path echo, ICMP path jitter, FTP, DNS, and DHCP, as well as multiple
operation scheduling and proactive threshold monitoring. It does not support VoIP service levels using
the gatekeeper registration delay operations measurements.
Before configuring any IP SLAs application, you can use the show ip sla application privileged EXEC
command to verify that the operation type is supported on your software image. This is an example of
the output from the command:
Switch# show ip sla application
IP SLAs
Version: 2.2.0 Round Trip Time MIB, Infrastructure Engine-II
Time of last change in whole IP SLAs: 22:17:39.117 UTC Fri Jun
Estimated system max number of entries: 15801
Estimated number of configurable operations: 15801
Number of Entries configured : 0
Number of active Entries : 0
Number of pending Entries : 0
Number of inactive Entries : 0
Supported Operation Types
Type of Operation to Perform: 802.1agEcho
Type of Operation to Perform: 802.1agJitter
Type of Operation to Perform: dhcp
Type of Operation to Perform: dns
Type of Operation to Perform: echo
Type of Operation to Perform: ftp
Type of Operation to Perform: http
Type of Operation to Perform: jitter
Type of Operation to Perform: pathEcho
Type of Operation to Perform: pathJitter
Type of Operation to Perform: tcpConnect
Type of Operation to Perform: udpEcho
IP SLAs low memory water mark: 21741224
Configuring the IP SLAs Responder
The IP SLAs responder is available only on Cisco IOS software-based devices, including some Layer 2
switches that do not support full IP SLAs functionality, such as a Catalyst 3750-X or 3560-X switch
running the LAN base feature set or a Catalyst 2960 switch.

Table of Contents

Other manuals for Cisco Catalyst 4500 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 4500 Series and is the answer not in the manual?

Cisco Catalyst 4500 Series Specifications

General IconGeneral
SeriesCatalyst 4500 Series
CategorySwitch
Layer SupportLayer 2, Layer 3
Form FactorModular chassis
StackableNo
Chassis Slots3, 6, 7, 10
Power Supply OptionsAC, DC
RedundancyPower supply, Supervisor engine
Network ManagementCisco IOS Software CLI, SNMP, Cisco Prime Infrastructure
FeaturesSecurity, QoS
Port DensityUp to 384 ports per chassis
Security Features802.1X, ACLs, DHCP Snooping, Dynamic ARP Inspection, IP Source Guard
Supervisor Engine8-E

Related product manuals