Cisco Catalyst 4500 Series Software Configuration Guide

77-7
Catalyst 4500 Series Switch, Cisco IOS Software Configuration Guide - Cisco IOS XE 3.9.xE and IOS 15.2(5)Ex
Chapter 77 Configuring Call Home
Configuring Call Home
To subscribe a destination profile to an alert group, perform this task:
Command Purpose
Step 1
Switch# configure terminal
Enters configuration mode.
Step 2
Switch(config)# call-home
Enters Call Home configuration submode.
Step 3
Switch(cfg-call-home)# alert-group
{all|configuration|diagnostic|
environment|inventory|syslog}
Enables the specified alert group. Use the
keyword all to enable all alert groups. By
default, all alert groups are enabled.
Step 4
Switch(cfg-call-home)# profile name
Enters the Call Home destination profile
configuration submode for the specified
destination profile.
Step 5
Switch(cfg-call-home-profile)#
subscribe-to-alert-group configuration
[periodic {daily hh:mm | monthly date hh:mm |
weekly day hh:mm}]
Subscribes this destination profile to the
Configuration alert group. The Configuration
alert group can be configured for periodic
notification, as described in the “Configuring
Periodic Notification” section on page 77-8.
Switch(cfg-call-home-profile)#
subscribe-to-alert-group all
Subscribes to all available alert groups.
Step 6
Switch(cfg-call-home-profile)#
subscribe-to-alert-group diagnostic
[severity catastrophic|disaster|
fatal|critical|major|minor|warning|
notification|normal|debugging]
Subscribes this destination profile to the
Diagnostic alert group. The Diagnostic alert
group can be configured to filter messages based
on severity, as described in the “Configuring
Message Severity Threshold” section on
page 77-8.
Step 7
Switch(cfg-call-home-profile)#
subscribe-to-alert-group environment
[severity catastrophic|disaster|
fatal|critical|major|minor|warning|
notification|normal|debugging]
Subscribes this destination profile to the
Environment alert group. The Environment alert
group can be configured to filter messages based
on severity, as described in the “Configuring
Message Severity Threshold” section on
page 77-8.
Step 8
Switch(cfg-call-home-profile)#
subscribe-to-alert-group inventory
[periodic {daily hh:mm | monthly date hh:mm |
weekly day hh:mm}]
Subscribes this destination profile to the
Inventory alert group. The Inventory alert group
can be configured for periodic notification, as
described in the “Configuring Periodic
Notification” section on page 77-8.
Step 9
Switch(cfg-call-home-profile)#
subscribe-to-alert-group syslog
[severity catastrophic|disaster|
fatal|critical|major|minor|warning|
notification|normal|debugging]
[pattern string]
Subscribes this destination profile to the Syslog
alert group. The Syslog alert group can be
configured to filter messages based on severity,
as described in the “Configuring Message
Severity Threshold” section on page 77-8. You
can specify a pattern to be matched in the syslog
message. If the pattern contains spaces, you
must enclose it in quotes (“”).
Step 10
Switch(cfg-call-home-profile)# exit
Exits the Call Home destination profile
configuration submode.

Cisco Catalyst 4500 Series Specifications

General

Series	Catalyst 4500 Series
Category	Switch
Layer Support	Layer 2, Layer 3
Form Factor	Modular chassis
Stackable	No
Chassis Slots	3, 6, 7, 10
Power Supply Options	AC, DC
Redundancy	Power supply, Supervisor engine
Network Management	Cisco IOS Software CLI, SNMP, Cisco Prime Infrastructure
Features	Security, QoS
Port Density	Up to 384 ports per chassis
Security Features	802.1X, ACLs, DHCP Snooping, Dynamic ARP Inspection, IP Source Guard
Supervisor Engine	8-E