d-Color MF4003/MF3303
H UTILITY MODE > 12. Supplementary explanation of utility mode
H-36
Function Name Contents Default setting When Enhanced Security mode is set to
“ON”
Server load reduction
transmission method
Select the sending method to reduce the load of the E-
mail server (SMTP).
OFF When [Stop URL when max. limit is
exceeded] or [Always Send via URL] is
selected, this option is set to [OFF].
SNMPv1/v2c To use when changing Write setting. Read/Write
enable
Only Read is enabled (not to be changed)
SNMP v3 Security Level
and auth/priv-password
To set the Security level for the Reading/Writing
Authority User which is used for SNMP v3.
auth/priv-
password
• The security level can be selected
from among [auth-password] and
[auth/priv-password].
• An 8-digit-or-more auth-password
and priv-password can both be set.
Print Data Capture To set whether to allow or restrict capturing the Print
Job Data.
Allow Restrict (not to be changed)
Network Setting Clear To clear the network setting through Web Connection. Enabled Restrict
Release Time Settings To set the period of time to be elapsed before the
access lock state is released.
5 min. The setting value should be 5 min. or
more (no value less than 5 can be set)
Destination Registration
Change by User
(Address Book and
Program destination)
- Allow Restrict (not to be changed)
Security Print User Box
Preview
- Thumbnail View,
Detail View, and
Document
Details are
enabled
Only Detail View is enabled before
password authentication (Mode 2)
Initialize (Network
Settings)
To clear the network-related settings. Enabled Restrict (not to be changed)
Image Log Transfer
Settings
Specifies whether to transfer the input or output image
data to the server using whenever machine inputs or
outputs image data.
OFF OFF (not to be changed)
Machine Update
Settings
To set firmware upgrading by Internet ISW, and enable
or disable various settings.
OFF OFF (not to be changed)
operation Ban release
time (CE Authentication)
To set the period of time to be elapsed before the
access lock state is released in CE password
authentication.
5 min. The setting value should be 5 min. or
more (no value less than 5 can be set)
E-mail RX Print To print an E-mail attachment, send an E-mail to the E-
mail address of this machine.
OFF OFF (not to be changed)
IWS Settings Set the operating environment of IWS (Internal Web
Server) function.
OFF OFF (not to be changed)
Report File Attachment Report File Attachment With Attachment Without Attachment (not to be changed)
Storage data backup To set whether to permit our service representative to
back up or restore the storage on this machine.
Restrict Restrict (not to be changed)
CS Remote Care CS Remote Care enables the machine and the
computer at CS Remote Care center to exchange data
through telephone/fax line, network or E-mail in order to
control the machine.
Usable Remote device setting disabled
Maintenance Mode
Access
To set whether to permit your service representative to
change [Administrator Settings] of a device without
authentication.
Restrict Restrict (not to be changed)
Simple Connection
Setting
To set the pairing method to connect to an Android/iOS
terminal.
QR Code
Display Setting:
OFF
OFF (not to be changed)
Enable NFC:
OFF
OFF (not to be changed)
Enable
Bluetooth LE:
OFF
OFF (not to be changed)
SSL Settings (WebDAV
Server Settings)
Specify whether to use the SSL for communication or
not.
Non-SSL Only SSL Only (not to be changed)
SSL Setting (OpenAPI
Settings)
Specify whether to use the SSL for communication or
not.
Non-SSL Only SSL Only (not to be changed)
Web Browser Setting Select whether to enable a Web Browser. OFF OFF
Remote Panel Settings Configure settings for remotely controlling the Control
Panel of this machine from another computer.
Client Settings:
OFF
OFF
Server Setting:
OFF
OFF
To Next Page
Loading...
Need help?
General