Olivetti d-Color MF4003 User Manual

I SERVICE MODE > 10. System 2
I-47
d-Color MF4003/MF3303
10.5.11SW No.135
• Setting for ID length of the HID Prox card
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 Reports that the 1st byte shows the ID length of the card, the
2nd byte and after shows the card ID.
00000000 / 00
00000001 01 Reports the card ID with the ID length including the 1st byte.
10.5.12SW No.143
• Expansion setting of the touch panel sensitive area when the web browser function is used
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 26 dots: 26 dots from the perimeter of the touch panel is a
nonsensitive area.
00000000 / 00
00000001 01 16 dots: 16 dots from the perimeter of the touch panel is a
nonsensitive area.
00000010 02 9 dots: 9 dots from the perimeter of the touch panel is a
nonsensitive area.
NOTE
▪ The sensitive area of the control panel can be expanded by selecting “16 dots” or “9 dots” on the software switch No.143. Note
that the control panel’s sensitive area expanded in this manner may not detect touches properly.
10.5.13SW No.145
HEX 01
• Switching to Auto detection for paper size in manual bypass tray
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 Enable 00000000 / 00
00000001 01 Disable
HEX 02
• Switching paper feed mode if the size of paper fed from the manual bypass tray is mismatched
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 Stop immediately 00000010 / 02
00000010 02 Stop accordingly
Stop immediately in the following cases as an exception.
• "1" is set at bit4 for the Switch No.145
• For jobs where center stapling, half-folding, tri-folding
and Z-folding are set with a finisher equipped
HEX 04
• Displaying message when the paper size in manual bypass tray is mismatched with the paper size specified on the control panel
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 Enable 00000000 / 00
00000100 04 Disable
HEX 08
• When running a copy cycle with originals placed on the original glass, and [Auto] is displayed in "Group/Sort" of the finishing function,
[Auto] will be set as default. ("Sort" and "Offset" will be executed when [Auto] is selected.)
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 Enable 00000000 / 00
00001000 08 Disable
HEX 10
• Switch-over settings of Duplex printing and Billing permission
• Setting for allowing/prohibiting billing on exited paper when a paper size error occurred at the time of duplex printing
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 Allow (billing on one side of the paper) 00000000 / 00
00010000 10 Prohibit
10.5.14SW No.146
HEX 04
• Setting for enabling use of Non-Image Area Erase, Centering, and Original Size when the book original is used in the fax/scanner mode
Bit Assignment HEX Assignment Details Default value (Bit/HEX)
00000000 00 Prohibits use of Non-Image Area Erase, Centering, and
Original Size.
00000000 / 00
00000100 04 Enables use of Non-Image Area Erase, Centering, and
Original Size.
Y119930-3
Service Manual

Olivetti d-Color MF4003 Specifications

General

Brand	Olivetti
Model	d-Color MF4003
Category	Copier
Language	English