d-Color MF4003/MF3303
P THEORY OF OPERATION > 8. FK-517
P-108
Original
length=Receive
d original
size*(1/a)
Optimum
paper
Selected paper size / Division operation
Priority 1 Priority 2 Priority 3 Priority 4 Priority 5 Priority 6 Priority 7 Priority 8
312 to 384 mm B4 B4/a % B5/a % B5S/84 % A3/a % A4/a % A4S/a % - -
Over 384 mm A3 A3/a % A4/a % B5S/84 % - - - - -
• a : Set magnification
B4 width at reception
Original
length=Receive
d original
size*(1/a)
Optimum
paper
Selected paper size / Division operation
Priority 1 Priority 2 Priority 3 Priority 4 Priority 5 Priority 6 Priority 7 Priority 8
189 mm or less B5 B5/a % B5S/71 % B4/a % A4S/82 % A4/a % A3/a % - -
189 to 384 mm B4 B4/a % B5/a % B5S/71 % A3/a % A4/a % A4S/82 % - -
Over 384 mm A3 A3/a % A4/a % A4S/82 % - - - - -
• a : Set magnification
A3 width at reception
Original
length=Receive
d original
size*(1/a)
Optimum
paper
Selected paper size / Division operation
Priority 1 Priority 2 Priority 3 Priority 4 Priority 5 Priority 6 Priority 7 Priority 8
219 mm or less A4 A4/a % A4S/69 % B4/85 % A3/a % - - - -
Over 219 mm A3 A3/a % A4/a % A4S/69 % - - - - -
• a : Set magnification
(2)Cassette / paper selection
• The cassette and paper selection is performed by using two parameters of the [Administrator Settings] -> [Fax Settings] -> [TX/RX
Settings].
• [Print Paper Selection]: Auto Select, Fixed Size, Priority Size: a
• [Tray Selection for RX Print]: Auto, Tray 1, Tray 2, Tray 3 and Tray 4: b
NOTE
▪ When “b” is fixed to tray 1, 2, 3 or 4, “a” becomes invalid.
▪ Only when “b” is set to Auto, “a” becomes valid.
▪ Only A3, B4 and A4 sizes can be selected for the fixed size and preferential size modes.
▪ Bypass cannot be specified as fix-tray.
▪ Page dividing function becomes invalid when the tray is fixed.
(3)Compulsory memory reception
• The function to enable to print out by operations without printing out documents at reception in the FAX communications.
(a)Related settings
Compulsory memory reception function
• Set in the [Service Mode] -> [FAX] > [System] -> [Display Setting].
• When this setting is set to “OFF”, display and actions related to the Compulsory memory reception are not performed. In addition, you
can not perform operations. If this setting is not set, the following Compulsory memory reception function used is also set to disabled.
Compulsory memory reception function use
• Set in the [Administrator Settings] -> [Fax Settings] -> [Function Settings] -> [Memory RX Setting].
• When this setting is set to “NO”, the compulsory memory reception actions are not performed at reception. In addition, you can not
display, erase and print the compulsory memory reception documents. The compulsory memory reception documents are displayed on
the main menu irrelevant to this setting.
Compulsory memory reception password
• Within eight digits (0 to 9)
• Set in the [Administrator Settings] -> [Fax Settings] -> [Function Settings] -> [Memory RX Setting].
• This setting is required to display, delete or print the compulsory memory reception documents.
(b)Operation
Necessary conditions for this function
• When there is the compulsory memory reception function, and it is used, the compulsory memory reception action is performed.
Line seizure
• It is possible to receive up to 500 compulsory memory reception jobs including the normal reception and the substitute reception.
When 500 compulsory memory reception jobs are received, machine will not catch the line. (Except the case that the polled
transmission documents and bulletin board documents are registered.)
Reception
• When the reception is performed in the compulsory memory reception mode, printing is not performed even with recording paper and
the reception is performed in memory as the compulsory memory reception documents.
• The same as in the polled reception and manual reception.
To Next Page
Loading...
Need help?
General