Sel 411L - Page 13

xi
Date Code 20151029 SEL-411L Relay
List of Tables
Table 5.10 Settings Group Selection..................................................................................................... P.5.6
Table 5.11 Data Reset Control.............................................................................................................. P.5.6
Table 5.12 Frequency Estimation.......................................................................................................... P.5.7
Table 5.13 Time-Error Calculation ....................................................................................................... P.5.7
Table 5.14 Current and Voltage Source Selection................................................................................. P.5.7
Table 5.15 Synchronized Phasor Measurement.................................................................................... P.5.7
Table 5.16 Time and Date Management ............................................................................................... P.5.8
Table 5.17 DNP3................................................................................................................................... P.5.9
Table 5.18 Protection Free-Form SEL
OGIC Control Equations............................................................ P.5.9
Table 5.19 Output Settings Categories................................................................................................ P.5.10
Table 5.20 Interface Board #1............................................................................................................. P.5.10
Table 5.21 Interface Board #2............................................................................................................. P.5.10
Table 5.22 Remote Analog Outputs.................................................................................................... P.5.11
Table 5.23 M
IRRORED BITS Transmit Equations ................................................................................ P.5.11
Table 5.24 87L Communication Bits Transmit Equations.................................................................. P.5.11
Table 5.25 Front-Panel Settings Categories........................................................................................ P.5.11
Table 5.26 Front-Panel Settings.......................................................................................................... P.5.12
Table 5.27 Selectable Screens for the Front Panel.............................................................................. P.5.15
Table 5.28 Selectable Operator Pushbuttons....................................................................................... P.5.16
Table 5.29 Front-Panel Event Display ................................................................................................ P.5.16
Table 5.30 Boolean Display Points..................................................................................................... P.5.17
Table 5.31 Analog Display Points....................................................................................................... P.5.17
Table 5.32 Local Control..................................................................................................................... P.5.17
Table 5.33 Local Bit SEL
OGIC............................................................................................................ P.5.17
Table 5.34 SER Parameters................................................................................................................. P.5.18
Table 5.35 Port Settings Categories .................................................................................................... P.5.18
Table 5.36 Protocol Selection ............................................................................................................. P.5.18
Table 5.37 Communications Settings.................................................................................................. P.5.19
Table 5.38 SEL Protocol Settings ....................................................................................................... P.5.19
Table 5.39 Fast Message Read Data Access ....................................................................................... P.5.19
Table 5.40 DNP3 Serial Protocol Settings.......................................................................................... P.5.20
Table 5.41 DNP3 LAN/WAN Settings................................................................................................ P.5.21
Table 5.42 M
IRRORED BITS Protocol Settings .................................................................................... P.5.22
Table 5.43 RTD Protocol Settings....................................................................................................... P.5.23
Table 5.44 PMU Protocol Settings...................................................................................................... P.5.23
Table 5.45 87L Port Settings............................................................................................................... P.5.23
Table 5.46 87L Channel Monitoring Settings..................................................................................... P.5.24
Table 5.47 87L Communications Bits Debounce Time Delay—Serial Communication................................P.5.24
Table 5.48 87L Communications Bits Debounce Time Delay—Ethernet Communication............................P.5.25
Table 5.49 DNP3 Settings Categories................................................................................................. P.5.25
Table 5.50 DNP3 Object Default Map Enables .................................................................................. P.5.25
Table 5.51 Binary Input Map .............................................................................................................. P.5.25
Table 5.52 Binary Output Map............................................................................................................ P.5.26
Table 5.53 Counter Map...................................................................................................................... P.5.26
Table 5.54 Analog Input Map ............................................................................................................. P.5.26
Table 5.55 Analog Output Map........................................................................................................... P.5.26
Table 5.56 Minimum and Maximum Fault Location.......................................................................... P.5.26
Table 5.57 Bay Settings....................................................................................................................... P.5.26
Table 6.1 SEL Software Solutions ...................................................................................................... P.6.1
Table 6.2
ACSELERATOR QuickSet Applications ............................................................................... P.6.2
Table 6.3
ACSELERATOR QuickSet Submenu Options....................................................................... P.6.2
Table 6.4
ACSELERATOR QuickSet HMI Tree View Functions.......................................................... P.6.6
Table 6.5 Help................................................................................................................................... P.6.21
Table 7.1 Front-Panel Inactivity Time-Out Setting............................................................................. P.7.3
Table 7.2 Metering Screens Enable Settings....................................................................................... P. 7.4
Table 7.3 SER Point Settings .............................................................................................................. P.7.7
Table 7.4 Display Point Settings—Boolean........................................................................................ P.7.9
Table 7.5 Display Point Settings—Analog ....................................................................................... P.7.10