IN.8 Index
T–T
SEL-411L Relay Date Code 20151029
terminal P.10.15–P.10.20
application example
P. 1 0. 1 6 –
P.10.17, P.10.19–P. 1 0 .2 0
TERSE
P. 1 0. 1 7
text-edit mode
P.10.18–P.10.20
time
P.7.31, P.1 5.61
Setting Groups
multiple setting
P.1 4.9
nonvolatile
P.14. 10
Settings
data access
C.1.11–C.1.12
SIR
P.3.155
SOTF
See Switch-Onto-Fault
Source to Line Impedance Ratio
See SIR
Specifications
P.1.13–P.1.20
Star Network Topology C.3.1, C.3.3
State Measurement
C.6.2
Station DC Battery System Monitor
See DC Battery System Monitor
Status
P.11.39
check relay status
P.10. 10–P.1 0.13
application example
ACSELERATOR QuickSet
software
P.10.11–P.10.12
front panel
P.10.12, P.10.13
terminal
P.10.10
CST command
P.11.40, P.15.17
STATUS command
P.15.53–P.15.54
Status Failure
P. 11 .3 8, P. 11 .4 0
front panel
P.7.36
Status Warning
P.11.38, P.11.40
front panel
P.7.35
Subsidence Current
P.3.248
See also Circuit Breaker Failure
Substation Automation
P. 14 .2
See also SEL
OGIC Control
Equations
SUM Command
P. 8. 2 7, P.15.55
See also Event Summary
Switch-Onto-Fault
P.1.3, P.3.217–
P.3.219
close signal monitor, CLSMON
P.3.217
duration
P.3.217
end
P.3.218
initiation
P.3.217
logic diagram
P.3.219
single pole
P.3.218
validation
P.3.217
Synchronism Check
P.4.49–P.4.63
alternate source 2
P.4.62–P.4.63
angle checks
P.4.57
block synchronism check
P.4.56
circuit breaker closing
P.4.52
enable logic
P.4.56
healthy voltage window
P.4.55
input angle compensation
P.4.53–
P.4.55
input voltage magnitude
compensation
P.4.53–P.4.55
no slip
P.4.57–P.4.58
PT connections
P.4.53
Relay Word bits
P. 4. 5 1–P.4.52
settings
P.4.50–P.4.51
single-phase voltage inputs
P.4.50
slip, no compensate
P.4.59–P.4.60
slip, with compensate
P.4.60–P.4.62
Synchrophasors
C.6.1–C.6.43
accuracy
C.6.5
analog quantities
C.6.25
Ethernet
C.6.31
Fast Operate
C.6.42
measurement
C.6.3
protocols
C37.118
C.6.28
Fast Message
C.6.38
Relay Word bits
C.6.23
setting example
C.6.31
settings
C.6.6–C.6.16, C.6.19
Time-Synchronized Metering
P.9.37
System Integration
C.3.1
T
TARGET Command P. 11 . 8 , P.15.56–
P.15.57
Targets
P.7.36–P.7 .40
front panel
P.7.2
instantaneous/time O/C
P.7 .4 0
operational
P.7.37
phases/ground
P.7.39
recloser status
P.7.40
regions
P.7.37
reset
P.7.37–P.7.38
trip type
P.7.38
zone activated
P. 7. 3 9
TCP/IP
FTP
anonymous user
C.1.11
Ethernet card related settings
C.1.11
file structure
C.1.11
Telnet
Ethernet card related settings
C.1.12
user interface access
C.1.12
TEST 87L command
P.1 1.5
characteristic test
P. 1 1. 5
loopback test
P. 1 1. 6 , P.11.26
TEST DB
See Commands
TEST DB Command
P.1 1. 8, P.15.57–
P.1 5.5 8
TEST DB2 Command P. 1 1 .8
TEST FM Command
P.11. 9, P.15.59–
P.1 5.6 1
TEST mode P.1 1.4
Testing
P.11.1–P.1 1.37
acceptance testing
P.1 1. 1
application example
P.11.31–P.11.34
ASCII commands
P.11 .7, P.11. 9
commissioning testing
P.11 .2
directional elements
P.11.30–
P.1 1. 34
application example
P.11.32–
P.1 1. 34
distance elements
P.11.34–P.11.37
application example
P.11.36–
P.1 1. 37
element tests
P.11.19–P. 1 1. 3 7
features
P.1 1. 6
low-level test interface
P. 11 .9 –
P.1 1. 10
maintenance testing
P. 11 .2 –P.1 1. 3
methods
P.11. 14 –P.11 .19
application example
control outputs
P. 1 1. 1 7 –
P.1 1. 19
targets, LCD
P.11.16–P.11.17
targets, terminal
P.11. 15
overcurrent elements
P.11.27–
P.1 1. 30
application example
P.11.28–
P.1 1. 30
self-tests
P.11.38–P.11.40
SER
P.11.19
Thermal Demand Metering
P.9.32
See also Demand Metering
Time
P. 13 .1 –P.1 3 .8
See also Synchrophasors
high-accuracy
P.13. 1–P. 13 .8
application example
P.13.2–
P.1 3. 4, P. 13 . 5 –P.13 .8
Relay Word bits
P. 13 .2 , P.1 3.3
Time Inputs
P.2.9, P.2.36
See also IRIG-B
connecting P. 13 . 3
IRIG-B
P.2.9
TIME Q Command
P. 13 . 4–P.13.5,
P.1 5.6 2
Time Synchronization P. 1 3. 1
See also Time Inputs
DNP3 C.4.10
GPS
C.6.5
IRIG-B
P.13.1, C.3.2, C.3.5, C.6.25
SEL-2407
C.6.1
To Next Page
Loading...
