Sel 411L - Figure 11.19 Relay Status from a STATUS a Command on a Terminal; Figure 11.20 Compressed ASCII Status Message

P.11.40
SEL-411L Relay Protection Manual Date Code 20151029
Testing and Troubleshooting
Relay Self-Tests
=>>STA A <Enter>
Relay 1 Date: 03/15/2001 Time: 04:48:49.938
Station A Serial Number: 2001001234
FIDSEL-411L-R101-V0-Z001001-D20010315 CID0x4572
Failures
No Failures
Warnings
No Warnings
Channel Offsets (mV) WWarn FFail
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 MOF
0 0 0 0 0 0 0 0 0 0 0 0 0
Power Supply Voltages (V) WWarn FFail
3.3V_PS 5V_PS N5V_PS 15V_PS N15V_PS
3.28 4.91 -4.93 14.70 -14.79
Temperature
23.7 degrees Celsius
Communication Interfaces
Active High Accuracy Time Synchronization Source: IRIG-B
IRIG-B Source PRESENT
SEL
OGIC Relay Programming Environment Errors
No Errors
Relay Enabled
=>>
Figure 11.19 Relay Status From a STATUS A Command on a Terminal
CSTATUS
The relay also reports status information in the Compressed ASCII format
when you issue the CST command. An example of a compressed ASCII status
message is shown in Figure 11.20.
"RID","SID","FID","yyyy",
"relay_name","station_name","SEL-411L-x-Rxx-Vx-Zxxxxxx-Dxxxxxxxx","yyyy"
"MONTH","DAY","YEAR","HOUR","MIN","SEC","MSEC","yyyy"
(Month),(Day),(Year),(Hour),(Min),(Sec),(MSec),"yyyy"
"CPU_RAM","CPU_PROG","SELBOOT","CPU_SET","DSP_RAM","DSP","DSP_CSUM","DSP_T_OUT","CPUDSP_RAM","FRNT_PNL","CAL_BOARDA",
"CCRD_CHG","COMM_CARD","ANA_CONV","IO_1","IO_2","yyyy"
"(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)",
"(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","yyyy"
"ATOD_OFFST","MSTR_OFFST","3.3V_PS","5V_PS","N5V_PS","15V_PS","N15V_PS","TEMP_STA","TEMP","PRT_O_LOAD","LCD_ERROR","FPGA",
"yyyy"
"(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)","(Ok or F)",(Temp value),"(Ok or F)",
"(Ok or F)","(Ok or F)","yyyy"
"MBA","MBB","ACTTIM_SRC","SELOG_MATH","FM_TEST","DB_TEST","DB2_TEST","RLY_STA","PRT_F_TP","PRT_1_TP","PRT_2_TP","PRT_3_TP",
"PRT_5_TP","yyyy"
(Inac or Ok or F),(Inac or Ok or F),(HIRIG or IRIG or " "),(Enabled or Disabled), (Enabled or Disabled), (Enabled or
Disabled), (Enabled or Disabled),(F,0-5), (F,0-5), (F,0-5), (F,0-5), (F,0-5),"yyyy"
Figure 11.20 Compressed ASCII Status Message
Definitions for the items and fields in the Compressed ASCII configuration
are listed below:
➤ yyyy is the checksum
➤ x is text in the FID (Firmware ID) string
➤ (description) is text that the relay supplies
➤ (Ok or W or F) is normal, warning, or failure, respectively