09/03
6-37
DC 3535/2240/1632, WC M24
746--xxx Xero Transfer NVM List
General Procedures and Information
Initial issue
746-091 Plain paper S Control NVM1 (BW
Side1)
0 0~1 0=Control -S-7 (For BW side 1 of Plain paper A~G)
1=Control -S-8 (For BW side 1 of paper applicable to the above)
746-092 Plain paper S Control NVM1 (FC Side2) DC2240/
1632=5
DC3535
=4
0~5 0=Control -S-9 (FCside2 secondary transfer output for P paper)
1=Control -S-10 (FCside2 secondary transfer output for recycle paper)
2=Control -S-11 (FCside2 secondary transfer output for 4024 20lb)
3=Control -S-12 (FCside2 secondary transfer output for of 4024 24lb)
4=Control -S-13 (FCside2 secondary transfer output for paper applicable to the 4 items described above)
5=Control -S-14 (FCside2 secondary transfer output based on the secondary transfer coefficient stored in the
undisclosed NVM locations 746-356~407)
746-408 Output Remote for DTS normal-speed
Side1
0 0~100 (1bit=1%) Displays the multiplication value for DTS output adjustment
746-409 Output Remote for DTS normal-speed
Side2
50 0~100 (1bit=1%) Displays the multiplication value for DTS output adjustment
746-410 Output Remote for DTS half-speed
Side1
100 0~100 (1bit=1%) Displays the multiplication value for DTS output adjustment
746-411 Output Remote for DTS half-speed
Side2
100 0~100 (1bit=1%) Displays the multiplication value for DTS output adjustment
746-412 Output Remote for DTS high-speed
Side1
0 0~100 (1bit=1%) Displays the multiplication value for DTS output adjustment
746-413 Output Remote for DTS high-speed
Side2
50 0~100 (1bit=1%) Displays the multiplication value for DTS output adjustment
746-423 Toner Band Width (in process direction) 3 0~22 (1bit=1mm) For adjustment of Toner Band Width in process direction
746-424 Toner Band Width (in axial direction) 137 0~137 For adjustment of Toner Band Width in axial direction (1bit=1mm)
746-425 Toner Band Density 60 10~100 For adjustment of Toner Band Density (1bit=1%)
746-959
DC2240/1632
2nd Cln Minus Bias Output (for Environ-
ment no.0, 1, 2, 3)
123 102~921 For 2ND BTR Cleaning Bias setup for each environment (1bit=-4.888V)
746-959
DC3535
2nd Cln Minus Bias Output (for Environ-
ment no.0, 1, 2, 3)
92 77~921 For 2ND BTR Cleaning Bias setup for each environment (1bit=-6.515V)
746-960
DC2240/1632
2nd Cln Minus Bias Output (for Environ-
ment no.4)
123 102~921 For 2ND BTR Cleaning Bias setup for each environment (1bit=-4.888V)
746-960
DC3535
2nd Cln Minus Bias Output (for Environ-
ment no.4)
92 77~921 For 2ND BTR Cleaning Bias setup for each environment (1bit=-6.515V)
746-961
DC2240/1632
2nd Cln Minus Bias Output (for Environ-
ment no.5, 6)
123 102~921 For 2ND BTR Cleaning Bias setup for each environment (1bit=-4.888V)
746-961
DC3535
2nd Cln Minus Bias Output (for Environ-
ment no.5, 6)
92 77~921 For 2ND BTR Cleaning Bias setup for each environment (1bit=-6.515V)
746-962
DC2240/1632
2nd Cln Minus Bias Output (for Environ-
ment no.7, 8, 9)
123 102~921 For 2ND BTR Cleaning Bias setup for each environment (1bit=-4.888V)
746-962
DC3535
2nd Cln Minus Bias Output (for Environ-
ment no.7, 8, 9)
92 77~921 For 2ND BTR Cleaning Bias setup for each environment (1bit=-6.515V)
746-963 Y offset distance 16 0~16 Distance between Drum contact and 1ST BTR (0ms~39ms - 1bit=1 msec.)
746-964 M offset distance 16 0~16 Distance between Drum contact and 1ST BTR (0ms~39ms - 1bit=1 msec.)
746-965 C offset distance 16 0~16 Distance between Drum contact and 1ST BTR (0ms~39ms - 1bit=1 msec.)
746-966 K offset distance 16 0~16 Distance between Drum contact and 1ST BTR (0ms~39ms - 1bit=1 msec.)
Table 1 Chain 746
Chain-Link Name Default Range Description
To Next Page
Loading...
