09/03
6-57
DC 3535/2240/1632, WC M24
760-xxx Regicon NVM List
General Procedures and Information
Initial issue
760-026 K-YSO 237 0~474 Adjusts the slow scan direction write start position by the #. of LS signal counts from the ROS/Image/Patch Start
signal. (1 pixel/bit)
760-027 Regi Con/Circum. Length Correction
implement SW
3 0~3 For check during servicing etc. 0=Does not perform Regi Control nor Circumference Length Correction 1=Per-
forms Regi Control, does not perform Circumference Length Correction 2=Does not perform Regi Control, per-
forms Circumference Length Correction 3=Performs Regi Control and Circumference Length Correction
760-028 RC Start Temp 40 10~250 Threshold of (Normal) Regi Control Implementation Temperature difference. Value is 10 times the temperature.
(0.1 degree Celsius interval)
760-029 OLRC implementation SW 1 0~1 0=Does not perform Open Loop Regi control; 1=Performs Open Loop Regi control
760-030 Y-OLRC Start Temp 30 10~100 Threshold of Yellow Open Loop Regi control implementation temperature difference. Value is 10 times the tem-
perature. (0.1 degree Celsius interval)
760-031 M-OLRC Start Temp 30 10~100 Threshold of Magenta Open Loop Regi control implementation temperature difference. Value is 10 times the
temperature. (0.1 degree Celsius interval)
760-032 K-OLRC Start Temp 30 10~100 Threshold of Black Open Loop Regi Control Implementation Temperature difference. Value is 10 times the tem-
perature. (0.1 degree Celsius interval)
760-033
DC3535
Lchev 100 0~255 Tolerance of color misregistration in lateral direction (2µm/bit)
760-034
DC5353
Pchev 100 0~255 Tolerance of color misregistration in lateral direction (2µm/bit)
760-035 Aok (for Diag Regi Con) 20 1~24 Threshold of No. of valid Blocks of fine adjustment pattern at Diag Regi Control (DC685). NG occurs if the value
is out corrected below the threshold.
760-036 Aok (for normal Regi Con) 8 1~12 Threshold of No. of valid Blocks of fine adjustment pattern at Normal Regi Control. NG occurs if the value is out
corrected below the threshold.
760-037 LEDset-IN-A 2 0~2 MOB LED On/Off and light quantity step at IN side. 0=Off; 1=Low; 2=High
760-038 LEDset-IN-B 2 0~2 MOB LED On/Off and light quantity step at IN side.0=Off; 1=Low 2;=High
760-039
DC5353
LED-IN-A-Low 12 0~60 Set current value when light quantity on the LED-A side of IN-MOB is Low
760-040
DC5353
LED-IN-A-High 25 0~60 Set current value when light quantity on the LED-A side of IN-MOB is High
760-041
DC5353
LED-IN-B-Low 12 0~60 Set current value when light quantity on the LED-b side of IN-MOB is Low
760-042
DC5353
LED-IN-B-High 25 0~60 Set current value when light quantity on the LED-B side of IN-MOB is High
760-043 LEDset-OUT-A 2 0~2 MOB LED On/Off and light quantity step at OUT side. 0=Off; 1=Low; 2=High
760-044 LEDset-OUT-B 2 0~2 MOB LED On/Off and light quantity step at OUT side 0=Off; 1=Low; 2=High
760-045
DC5353
LED-OUT-A-Low 12 0~60 Set current value when light quantity on the LED-A side of OUT-MOB is Low
760-046
DC5353
LED-OUT-A-High 25 0~60 Set current value when light quantity on the LED-A side of OUT-MOB is High
760-047
DC5353
LED-OUT-B-Low 12 0~60 Set current value when light quantity on the LED-b side of OUT-MOB is Low
760-048
DC5353
LED-OUT-B-High 25 0~60 Set current value when light quantity on the LED-B side of OUT-MOB is High
760-049 Y-XBI 0 0~3 Adjusts fast scan direction write start position by switching the video clock phase from SOS signal.
(DC 2240/1632=1 pixel/bit; DC 3535=1/5 pixel/bit)
Table 1 Chain 760
Chain-Link Name Default Range Description
To Next Page
Loading...
