09/03
6-44
DC 3535/2240/1632, WC M24
752-xxx Procon NVM List
Initial issue
General Procedures and Information
752-081 ATC Average [Y] 0 0~1023 ATC Average detected value after sensor sensitivity correction
752-082 ATC Average [M] 0 0~1023 ATC Average detected value after sensor sensitivity correction
752-083 ATC Average [C] 0 0~1023 ATC Average detected value after sensor sensitivity correction
752-084 ATC Average [K] 0 0~1023 ATC Average detected value after sensor sensitivity correction
752-089 ATC Fluctuation [Y] 0 0~1023 ATC Fluctuation Range detected value after sensor sensitivity correction
752-090 ATC Fluctuation [M] 0 0~1023 ATC Fluctuation Range detected value after sensor sensitivity correction
752-091 ATC Fluctuation [C] 0 0~1023 ATC Fluctuation Range detected value after sensor sensitivity correction
752-092 ATC Fluctuation [K] 0 0~1023 ATC Fluctuation Range detected value after sensor sensitivity correction
752-109 Number of Continuous ATC Fails [Y] 0 0~255 No. of Continuous ATC Fails
752-110 Number of Continuous ATC Fails [M] 0 0~255 No. of Continuous ATC Fails
752-111 Number of Continuous ATC Fails [C] 0 0~255 No. of Continuous ATC Fails
752-112 Number of Continuous ATC Fails [K] 0 0~255 No. of Continuous ATC Fails
752-114 Warn ATC Max & min. [Y] 0 0~2 ATC Upper and Lower Limits Warning (0=Normal, 1=ATC Output low HiTC, 2=ATC Output high LowTC)
752-115 Warn ATC Max & min. [M] 0 0~2 ATC Upper and Lower Limits Warning (0=Normal, 1=ATC Output low HiTC, 2=ATC Output high LowTC)
752-116 Warn ATC Max & min. [C] 0 0~2 ATC Upper and Lower Limits Warning (0=Normal, 1=ATC Output low HiTC, 2=ATC Output high LowTC)
752-117 Warn ATC Max & min. [K] 0 0~2 ATC Upper and Lower Limits Warning (0=Normal, 1=ATC Output low HiTC, 2=ATC Output high LowTC)
752-118 Warn ATC Fluctuation Max & min. [Y] 0 0~2 ATC Fluctuation Range Lower Limit Warning (0=Normal, 1=To little fluctuation)
752-119 Warn ATC Fluctuation Max & min. [M] 0 0~2 ATC Fluctuation Range Lower Limit Warning (0=Normal, 1=To little fluctuation)
752-120 Warn ATC Fluctuation Max & min. [C] 0 0~2 ATC Fluctuation Range Lower Limit Warning (0=Normal, 1=To little fluctuation)
752-121 Warn ATC Fluctuation Max & min. [K] 0 0~2 ATC Fluctuation Range Lower Limit Warning (0=Normal, 1=To little fluctuation)
752-122 Fail ATC Patch [Y] 0 0~1 ATC Sensor Fail
752-123 Fail ATC Sensor [M] 0 0~1 ATC Sensor Fail
752-124 Fail ATC Sensor [C] 0 0~1 ATC Sensor Fail
752-125 Fail ATC Sensor [K] 0 0~1 ATC Sensor Fail
752-130 Set ATC Control Nominal Value [0] [Y] * 0~1023 ATC Control Nominal Value before environment/deterioration correction as center setup
*default=602 for DC2240/1632; 595 for DC3535
752-131 Set ATC Control Nominal Value [0] [M] * 0~1023 ATC Control Nominal Value before environment/deterioration correction as center setup
*default=602 for DC2240/1632; 595 for DC3535
752-132 Set ATC Control Nominal Value [0] [C] * 0~1023 ATC Control Nominal Value before environment/deterioration correction as center setup
*default=602 for DC2240/1632; 595 for DC3535
752-133 Set ATC Control Nominal Value [0] [K] * 0~1023 ATC Control Nominal Value before environment/deterioration correction as center setup
*default=602 for DC2240/1632; 595 for DC3535
752-134 Set ATC Control Nominal Value [1] [Y] * 0~1023 ATC Control Nominal Value before environment/deterioration correction as center setup
*default=642 for DC2240/1632; 645 for DC3535
752-135 Set ATC Control Nominal Value [1] [M] * 0~1023 ATC Control Nominal Value before environment/deterioration correction as center setup
*default=642 for DC2240/1632; 645 for DC3535
752-136 Set ATC Control Nominal Value [1] [C] * 0~1023 ATC Control Nominal Value before environment/deterioration correction as center setup
*default=642 for DC2240/1632; 645 for DC3535
752-137 Set ATC Control Nominal Value [1] [K] * 0~1023 [ATC Control Nominal Value before environment/deterioration correction as center setup
*default=652 for DC2240/1632; 645 for DC3535
752-138 Set ATC Control Nominal Value [2] [K] * 0~1023 ATC Control Nominal Value before environment/deterioration correction as center setup
Table 1 Chain 752
Chain-Link Name Default Range Description
To Next Page
Loading...
