xxxi
Date Code 20151029 SEL-411L Relay
List of Figures
Figure 15.1 Sample ETH Command Response.................................................................................. P.15.20
Figure 15.2 GOOSE Command Response.......................................................................................... P.15.26
Figure 15.3 Sample ID Command Response From Ethernet Card..................................................... P.15.29
Figure 15.4 Sample MAC Command Response................................................................................. P.15.31
Figure 15.5 Response to the MET DIF Command............................................................................. P.15.35
Figure 15.6 Sample PING Command Response................................................................................. P.15.41
Figure 15.7 Sample VER Command Response.................................................................................. P.15.63
Figure B.1 Prepare the Device (Step 1 of 4) .........................................................................................P.B.4
Figure 3 Load Firmware (Step 2 of 4)...............................................................................................P.B.5
Figure B.2 Load Firmware (Step 3 of 4)...............................................................................................P.B.6
Figure B.3 Verify Device Settings (Step 4 of 4)....................................................................................P.B.7
Figure B.4 Example Relay STA A Command Results..........................................................................P.B.9
Figure B.5 Transferring New Firmware..............................................................................................P.B.12
Communications Manual
Figure 1.1 Relay 4U Chassis Front-Panel Layout ................................................................................C.1.2
Figure 1.2 Relay 4U Rear-Panel Layout...............................................................................................C.1.3
Figure 1.3 EIA-232 Connector Pin Numbers .......................................................................................C.1.3
Figure 1.4 Failover Network Topology.................................................................................................C.1.9
Figure 1.5 Self-Healing Ring Using Internal Ethernet Switch...........................................................C.1.10
Figure 1.6 MAP 1:METER Command Example................................................................................C.1.24
Figure 2.1 SEL-2600A RTD Module and the Relay ..........................................................................C.2.18
Figure 2.2 MET T Command Response.............................................................................................C.2.19
Figure 2.3 MET T Command Response for Status Problem..............................................................C.2.20
Figure 2.4 HTTP Server Login Screen...............................................................................................C.2.22
Figure 2.5 HTTP Server Home Page and Response to Version Menu Selection ...............................C.2.23
Figure 2.6 Web Server Show Settings Screen ....................................................................................C.2.24
Figure 3.1 SEL Communications Processor Star Integration Network................................................C.3.1
Figure 3.2 Multitiered SEL Communications Processor Architecture.................................................C.3.2
Figure 3.3 Enhancing Multidrop Networks With the SEL Communications Processors.....................C.3.4
Figure 3.4 Example SEL Relay and SEL Communications Processors Configuration........................C.3.5
Figure 4.1 DNP3 Multidrop Network Topology ..................................................................................C.4.4
Figure 4.2 DNP3 Star Network Topology ............................................................................................C.4.5
Figure 4.3 DNP3 Network With Communications Processor..............................................................C.4.5
Figure 4.4 Sample Response to SHO D Command............................................................................C.4.40
Figure 4.5 Sample Custom DNP3 Analog Input Map Settings..........................................................C.4.42
Figure 4.6 DNP3 Application Network Diagram...............................................................................C.4.42
Figure 4.7 Relay Example DNP Map Settings...................................................................................C.4.44
Figure 4.8 DNP3 LAN/WAN Application Example Ethernet Network.............................................C.4.46
Figure 4.9 Add Binary Inputs to SER Point List................................................................................C.4.48
Figure 5.1 Relay Predefined Reports....................................................................................................C.5.7
Figure 5.2 Relay Datasets.....................................................................................................................C.5.9
Figure 5.3 GOOSE Quality Attributes................................................................................................C.5.10
Figure 6.1 High-Accuracy Clock Controls Reference Signal (60 Hz System) ....................................C.6.3
Figure 6.2 Waveform at Relay Terminals May Have a Phase Shift......................................................C.6.3
Figure 6.3 Correction of Measured Phase Angle..................................................................................C.6.4
Figure 6.4 Example Calculation of Real and Imaginary Components of Synchrophasor....................C.6.5
Figure 6.5 TCP Connection................................................................................................................C.6.17
Figure 6.6 UDP_T and UDP_U Connections.....................................................................................C.6.18
Figure 6.7 UDP_S Connection ...........................................................................................................C.6.18
Figure 6.8 Sample MET PM Command Response.............................................................................C.6.28
Figure 6.9 Real-Time Control Application.........................................................................................C.6.34
Figure 6.10 Local Relay SEL
OGIC Settings..........................................................................................C.6.35
Figure 6.11 Remote Relay SEL
OGIC Settings ......................................................................................C.6.35
Figure 6.12 Remote Relay Global Settings ..........................................................................................C.6.35
Figure 6.13 Local Relay Global Settings..............................................................................................C.6.36
Figure 6.14 Remote Relay Port Settings...............................................................................................C.6.36
To Next Page
Loading...
