R&S ZNB Series - Page 1268

Command reference
R&S
®
ZNB/ZNBT
1268User Manual 1173.9163.02 ─ 62
Option R&S ZNB-B1, Bias Tees
If option R&S ZNB-B1 is installed on a R&S ZNB4 or R&S ZNB8, the frequency range
starts at 100 kHz.
Bias Tees are not available for the R&S ZNBT.
[SENSe<Ch>:]FREQuency:CENTer............................................................................... 1268
[SENSe<Ch>:]FREQuency:CONVersion........................................................................ 1269
[SENSe<Ch>:]FREQuency:CONVersion:ARBitrary..........................................................1270
[SENSe<Ch>:]FREQuency:CONVersion:ARBitrary:PMETer<Pmtr>...................................1270
[SENSe<Ch>:]FREQuency:CONVersion:GAIN:LMCorrection........................................... 1271
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:FIXed<Stg>.............................................1271
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:FUNDamental......................................... 1272
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:IFPort..................................................... 1272
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:LOMultiplier<Stg>.................................... 1273
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:LOPort<Stg>........................................... 1273
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:MFFixed................................................. 1274
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:RFMultiplier.............................................1275
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:RFPort....................................................1276
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:STAGes.................................................. 1276
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:TFRequency<Stg>...................................1276
[SENSe<Ch>:]FREQuency[:CW]................................................................................... 1277
[SENSe<Ch>:]FREQuency:FIXed..................................................................................1277
[SENSe<Ch>:]FREQuency:IMODulation:CONVersion......................................................1278
[SENSe<Ch>:]FREQuency:IMODulation:LTONe............................................................. 1278
[SENSe<Ch>:]FREQuency:IMODulation:ORDer<Im>[:STATe].......................................... 1279
[SENSe<Ch>:]FREQuency:IMODulation:RECeiver..........................................................1279
[SENSe<Ch>:]FREQuency:IMODulation:SPECtrum:MORDer...........................................1280
[SENSe<Ch>:]FREQuency:IMODulation:SPECtrum[:STATe]............................................ 1280
[SENSe<Ch>:]FREQuency:IMODulation:TDIStance........................................................ 1281
[SENSe<Ch>:]FREQuency:IMODulation:UTONe.............................................................1282
[SENSe<Ch>:]FREQuency:SBANd................................................................................1282
[SENSe<Ch>:]FREQuency:SEGMent:AXIS.................................................................... 1283
[SENSe<Ch>:]FREQuency:SPAN..................................................................................1284
[SENSe<Ch>:]FREQuency:STARt................................................................................. 1284
[SENSe<Ch>:]FREQuency:STOP..................................................................................1284
[SENSe<Ch>:]FREQuency:CENTer <CenterFreq>
Defines the center of the measurement and display range for a frequency sweep
(sweep range). The default center frequency is the center of the analyzer's maximum
frequency range: (f
MIN
+ f
MAX
)/2. The range depends on the instrument model; see
Table 7-17.
Suffix:
<Ch>
.
Channel number
SCPI command reference