R&S ZNB Series - 7.3.3 CONTrol commands

Command reference
R&S
®
ZNB/ZNBT
1074User Manual 1173.9163.02 ─ 62
7.3.3 CONTrol commands
The Control... commands allow you to configure the following interfaces:
●
User Port
●
Handler I/O connector (Universal Interface, option R&S ZN-B14 / R&S ZNBT-Z14)
●
RFFE GPIO interface (option R&S ZN-B15 / R&S ZN-Z15)
CONTrol:AUXiliary:C[:DATA]......................................................................................... 1075
CONTrol<Ch>:GPIO<Port>:RANGe...............................................................................1077
CONTrol:GPIO<Port>:SENSe:CURRent?.......................................................................1077
CONTrol:GPIO:SENSe:SUMCurrent?............................................................................ 1078
CONTrol<Ch>:GPIO:SENSe:TRIGger............................................................................1078
CONTrol:GPIO<Port>:SENSe:VOLTage?....................................................................... 1078
CONTrol<Ch>:GPIO<Port>:SHUNt?.............................................................................. 1079
CONTrol<Ch>:GPIO<Port>[:STATe]............................................................................... 1080
CONTrol<Ch>:GPIO:TIME............................................................................................ 1080
CONTrol<Ch>:GPIO<Port>:VOLTage[:DEFault].............................................................. 1080
CONTrol<Ch>:GPIO:VOLTage:OUTPut..........................................................................1081
CONTrol:HANDler:A[:DATA]..........................................................................................1081
CONTrol:HANDler:B[:DATA].......................................................................................... 1081
CONTrol:HANDler:C[:DATA]..........................................................................................1081
CONTrol:HANDler:D[:DATA]..........................................................................................1081
CONTrol:HANDler:E[:DATA].......................................................................................... 1081
CONTrol:HANDler:F[:DATA].......................................................................................... 1081
CONTrol:HANDler:G[:DATA]..........................................................................................1081
CONTrol:HANDler:H[:DATA]..........................................................................................1081
CONTrol:HANDler:A:MODE.......................................................................................... 1082
CONTrol:HANDler:B:MODE.......................................................................................... 1082
CONTrol:HANDler:C:MODE.......................................................................................... 1082
CONTrol:HANDler:D:MODE.......................................................................................... 1082
CONTrol:HANDler[:EXTension]:INDex:STATe..................................................................1082
CONTrol:HANDler[:EXTension]:RTRigger:STATe.............................................................1083
CONTrol:HANDler:INPut?............................................................................................. 1083
CONTrol:HANDler:LOGic..............................................................................................1083
CONTrol:HANDler:OUTPut<Pt>[:DATA]..........................................................................1084
CONTrol:HANDler:OUTPut<Pt>:USER...........................................................................1084
CONTrol:HANDler:PASSfail:LOGic................................................................................ 1085
CONTrol:HANDler:PASSfail:MODE................................................................................1085
CONTrol:HANDler:PASSfail:POLicy............................................................................... 1086
CONTrol:HANDler:PASSfail:SCOPe...............................................................................1086
CONTrol:HANDler:PASSfail:STATus?.............................................................................1087
CONTrol:HANDler:RESet..............................................................................................1087
CONTrol:HANDler:SWEepend.......................................................................................1087
CONTrol<Ch>:RFFE<Bus>:COMMand:DATA................................................................. 1088
CONTrol<Ch>:RFFE<Bus>:COMMand:SEND................................................................ 1088
CONTrol<Ch>:RFFE<Bus>:COMMand:SEND?...............................................................1088
CONTrol<Ch>:RFFE<Bus>:SETTings:FREQuency......................................................... 1089
CONTrol<Ch>:RFFE<Bus>:SETTings[:STATe]................................................................ 1089
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:HIGH.....................................................1089
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:IO......................................................... 1089
SCPI command reference