1268 Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
Index
base 10 exponential math function, 327, 347
base value measurement, 421, 458
base, ARINC 429, 637
base, I2S serial decode, 691
base, MIL-STD-1553 serial decode, 733
base, UART trigger, 769
basic instrument functions, 163
baud rate, 660, 721, 758
begin acquisition, 199, 219, 221
BHARris window for minimal spectral
leakage, 337
binary block data, 158, 304, 862, 969
BINary waveform data format, 622
bind levels for masks, 516
bit order, 759
bit order, SPI decode, 740
bit selection command, bus, 243
bit weights, 168
bitmap display, 304
bits in Service Request Enable Register, 181
bits in Standard Event Status Enable
Register, 166
bits in Status Byte Register, 183
bits selection command, bus, 244
blank, 198
block data, 158, 171, 862
block response data, 68
blocking synchronization
, 1129
blocking wait, 1128
BMP format screen image data, 304
braces, 157
built-in measurements, 61
burst data demo signal, 282
burst width measurement, 410
burst, minimum time before next, 898
bus bit selection command, 243
bus bits selection commands, 244
bus clear command, 246
bus commands, 242
BUS data format, 966
bus display, 247
bus label command, 248
bus mask command, 249
BUS<n> commands, 241
button disable, 856
button, calibration protect, 256
byte format for data transfer, 965, 971
BYTeorder, 967
C
C, SICL library example, 1228
C, VISA library example, 1181
C#, SCPI.NET example, 1248
C#, VISA COM example, 1157
C#, VISA example, 1200
CAL PROTECT button, 256
CAL PROTECT switch, 251
calculating preshoot of waveform, 436
calculating the waveform overshoot, 430
calibrate, 253, 254, 256, 260
CALibrate commands, 251
calibrate date, 253
calibrate introduction, 251
calibrate label, 254
calibrate output, 255
calibrate start, 257
calibrate status, 258
calibrate switch, 256
calibrate temperature, 259
calibrate time, 260
CAN acknowledge, 659
CAN and LIN demo signal, 284
CAN baud rate, 660
CAN demo signal, 283
CAN frame counters, reset, 656
CAN SEARch commands, 808
CAN serial bus commands, 652
CAN serial search, data, 810
CAN serial search, data length, 811
CAN serial search, ID, 812
CAN serial search, ID mode, 813
CAN serial search, mode
, 809
CAN signal definition, 661
CAN source, 662
CAN trigger, 663, 666
CAN trigger data pattern, 665
CAN trigger ID pattern, 667
CAN trigger pattern id mode, 668
CAN triggering, 629
capture data, 199
capturing data, 60
cardiac waveform generator output, 1009
center frequency set, 326, 334
center of screen, 994
center reference, 870
center screen, vertical value at, 346, 350
channel, 225, 269, 1049, 1051
channel coupling, 265
channel display, 266
channel input impedance, 267
channel inversion, 268
channel label, 269, 1050
channel labels, 305, 306
channel numbers, 1056
channel overload, 276
channel protection, 276
channel reset conditions, 176, 858
channel selected to produce trigger, 915, 947
channel signal type, 275
channel skew for oscilloscope probe, 274,
1052
channel status, 222, 1056
channel threshold, 1051
channel vernier, 280
channel, stop displaying, 198
CHANnel<n> commands, 261, 263
channels to autoscale, 196
channels, how autoscale affects, 193
characters to display, 854
chart logic bus state math function, 327, 347
chart logic bus state, clock edge, 329
chart logic bus state, clock source, 328
chart logic bus timing math function, 327, 347
chart logic bus, units, 332
chart logic bus, value for data = 0, 331
chart logic bus, value for data increment, 330
classes of input signals, 337
classifications, command, 1138
clear, 303
clear bus command, 246
clear cumulative edge variables, 1049
clear markers, 411, 1067
clear measurement, 411, 1067
clear message queue, 165
Clear method, 63
clear reference waveforms, 1035
clear screen,
1057
clear status, 165
clear waveform area, 298
clipped high waveform data value, 969
clipped low waveform data value, 969
clock, 709, 741, 744
clock slope, I2S, 692
CLOCk source, I2S, 694
clock source, setup and hold trigger, 934
clock timeout, SPI, 742
clock with infrequent glitch demo signal, 282
CLS (Clear Status), 165
CME (Command Error) status bit, 166, 168
CMOS threshold voltage for digital
channels, 295, 1051
CMOS trigger threshold voltage, 1094
code, :ACQuire:COMPlete, 229
code, :ACQuire:SEGMented, 235
code, :ACQuire:TYPE, 240
code, :AUToscale, 194
code, :CHANnel<n>:LABel, 269
code, :CHANnel<n>:PROBe, 271
code, :CHANnel<n>:RANGe, 277
code, :DIGitize, 200
code, :DISPlay:DATA, 304
code, :DISPlay:LABel, 305
code, :DISPlay:ORDer, 1056
code, :MEASure:PERiod, 445
code, :MEASure:RESults, 438
code, :MEASure:TEDGe, 453
code, :MTESt, 491
code, :POD<n>:THReshold, 527
code, :RUN/:STOP, 219
code, :SYSTem:SETup, 862
code, :TIMebase:DELay, 1093
code, :TIMebase:MODE, 867
code, :TIMebase:RANGe, 869
code, :TIMebase:REFerence, 870
code, :TRIGger:MODE, 886
code, :TRIGger:SLOPe, 905
code, :TRIGger:SOURce, 906
code, :VIEW and :BLANk, 225
code, :WAVeform, 982
code, :WAVeform:DATA, 969
code, :WAVeform:POINts, 973
code, :WAVeform:PREamble, 977
code, :WAVeform:SEGMented, 235
code, *RST, 178
code, SCPI.NET library example in C#, 1248
To Next Page
Loading...
Need help?
General
