Epson AcuLaser CX11 Service Manual

EPSON AcuLaser CX11/CX11F Revision B
APPENDIX Fax Unit System 662
OPERATOR CALL ERROR
Table 7-23. Operator Call Error
External
error code
Internal
Code
Description Cause Remedies
Panel
Display
(reference)
Report Display
Trigger for
Stopping
Operation
Notification Message
MAIN SUB
300 000 0x3000
Sending a fax is attempted at the time of receiving a fax Not used --- --- --- --- ---
300 001 0x3001
NSS/DCS function used by the received fax does not
meet those of the product
It is more likely that there
is something wrong with
the sending machine
Confirm if the sending
machine is normal.
*1, *2 Receiving failure 50H: Forced stop Receiving a fax is finished
300 002 0x3002
Abnormal commands are received from the other end
machine.
The other end machine
failure
Confirm the condition of
the other end machine,
and resend the fax. Or
ask the sender to resend
the fax if the error occurs
during receiving process.
*1, *2 Transmitting failure
Receiving failure
50H: Forced stop Transmitting a fax is
finishedReceiving a fax is
finished
300 003 0x3003
CS becomes ON in FSK method Not used --- --- --- --- ---
300 004 0x3004
Overrun Noises in the line or GND,
or loose connection of the
modular cable, or etc.
Check the line, GND, and
the modular cable, and try
the failed operation again
*3 Transmitting failure
Receiving failure
50H: Forced stop Transmitting a fax is finished
Receiving a fax is finished
300 005 0x3005
Underrun Noises in the line or GND,
or loose connection of the
modular cable, or etc.
Check the line, GND, and
the modular cable, and try
the failed operation again
*3 Transmitting failure
Receiving failure
50H: Forced stop Transmitting a fax is finished
Receiving a fax is finished
300 006 0x3006
CS of the modem did not become ON for RS request
while training in high speed
Noises in the line or GND,
or loose connection of the
modular cable, or etc.
Check the line, GND, and
the modular cable, and try
the failed operation again
*3 Transmitting failure 50H: Forced stop Transmitting a fax is finished
300 007 0x3007
The product received illegal commands from the other
end machine after receiving a communication reserve
request signal
The other end machine
failure
Confirm the condition of
the other end machine,
and try the failed
operation.
*3 Transmitting failure
Receiving failure
50H: Forced stop Transmitting a fax is finished
Receiving a fax is finished
300 008 0x3008
The product received RTN/PIN when transmitting in
G3 mode
Line quality is not good
Ask the recipient if the
fax was sent correctly,
and resend the fax as
necessary.
*3 Transmitting failure 50H: Forced stop Transmitting a fax is finished
300 009 0x3009
The product sent RTN when receiving in G3 mode Line quality is not good Ask the sender to resend
the fax if necessary.
*3 Receiving failure 50H: Forced stop Receiving a fax job is
finished
300 010 0x300A
The product sent EOR-Q when transmitting ECM Line quality is not good Confirm the condition of
the other end machine,
and try the failed
operation.
*3 Transmitting failure 50H: Forced stop Transmitting a fax is finished
manuals4you.commanuals4you.com

Epson AcuLaser CX11 Specifications

General

Brand	Epson
Model	AcuLaser CX11
Category	All in One Printer
Language	English