EasyManuals Logo

Epson AcuLaser CX11 Service Manual

Epson AcuLaser CX11
668 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #650 background imageLoading...
Page #650 background image
EPSON AcuLaser CX11/CX11F Revision B
APPENDIX Fax Unit System 652
COM_V34_SHIFT_G3 310 019
---
0B0
Enables or disables shifting to G3 mode when V34_CC time-out
occurs.
Set whether shift or not to shift to usual G3 mode when
COM_V34_CC_TIME time-out occurs.
If this is set to shift to G3 mode, it may happen to infringe
certain patent.
0 = Not allow
1 = Allow
Not allow
(0)
---
COM_V34_ENABLE 310 020
---
0B1
Enables or disables the V.34 ability
Set whether enables or disables V.34 performance regarding the
modulation method.
0 = Disable
1 = Enable
Enable
(1)
---
COM_ANSAM_TX_TIME 310 021
---
0B2
ANSam signal maximum transmitting time 0.1 to 25.5 sec (1 step = 100 ms) 4.0 seconds
(40)
---
COM_ANSAM_START_DELAY 310 022
---
0B3
Time interval until ANSam signal is transmitted
Set the time interval to start transmitting ANSam signal after the
line gets disconnected.
0.1 to 25.5 sec (1 step = 100 ms) 2.2 seconds
(22)
---
COM_V34_FRAME_SIZE 310 023
---
0B4
Frame size when transmitting V.34
0 = 256 octets
1 = 64 octets
256 octets
(0)
---
COM_ECM_ENABLE 310 024
---
0B5
Enables or disables the ECM performance (auto resending
function)
When line fault occurs in the middle of sending a fax, the function
allows the fax to be resend automatically immediately after the line
is restored.
0 = Disable
1 = Enable
Enable
(1)
---
COM_RTN_TX_RATE 310 034
---
0B6
RTN command transmitting criterion (percentage)
RTN: Indicates that training is required because messages are not
received correctly.
0 to 100 % (1 step = 1%)
5%
(5)
---
COM_RTN_TX_LINE 310 035
---
0B7
RTN command transmitting criterion (number of continuous lines) 0 to 255 lines (1 step = 1 line)
5 lines
(5)
---
COM_T1_TIME_CALL 310 036
---
0B8
T1 timer immediately after dialing 0 to 255 sec (1 step = 1 sec) 50 seconds
(50)
---
COM_T1_TIME_TX 310 037
---
0B9
T1 timer when transmitting a fax 0 to 255 sec (1 step = 1 sec) 36 seconds
(36)
---
COM_T1_TIME_RX 310 038
---
0BA
T1 timer when receiving a fax 0 to 255 sec (1 step = 1 sec) 39 seconds
(39)
---
COM_T2_TIME 310 039
---
0BB
T2 timer 0 to 25.5 sec (1 step = 100 ms) 6 seconds
(60)
---
COM_T3_TIME 310 040
---
0BC
T3 timer 0 to 25.5 sec (1 step = 100 ms) 15 seconds
(150)
---
Table 7-19. List of System Parameter (Communication Control)
Label
Maintenanc
e Code
User
Access
Internal
Address
Description Setting Value Default
Remark
s
Main Sub
C A U T I O N
manuals4you.commanuals4you.com

Table of Contents

Other manuals for Epson AcuLaser CX11

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Epson AcuLaser CX11 and is the answer not in the manual?

Epson AcuLaser CX11 Specifications

General IconGeneral
BrandEpson
ModelAcuLaser CX11
CategoryAll in One Printer
LanguageEnglish

Related product manuals