Agilent Technologies InfiniiVision 3000 X-Series Programmer's Guide

1270 Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
Index
digital channels, 6
digital channels, activity and logic levels
on, 191
digital channels, groups of, 523, 525, 527
digital pod, stop displaying, 198
digital reset conditions, 177, 859
DIGital<d> commands, 289
digitize channels, 199
DIGitize command, 60, 65, 962
digits, 158
disable front panel, 856
disable function, 1060
disabling calibration, 256
disabling channel display, 266
disabling status register bits, 166, 180
discontinued and obsolete commands, 1043
display annotation, 299
display annotation background, 300
display annotation color, 301
display annotation text, 302
display channel labels, 305
display clear, 303
DISPlay commands, 297
display commands introduction, 298
display connect, 1055
display date, 853
display factors scaling, 271
display for channels, 266
display frequency span, 335
display measurements,
406, 443
display order, 1056
display persistence, 307
display reference, 868, 870
display reference waveforms, 1036
display reset conditions, 177, 859
display serial number, 220
display vectors, 308
display wave position, 1056
display, lister, 377
display, measurement statistics on/off, 447
display, oscilloscope, 291, 307, 333, 525, 854
display, serial decode bus, 632
displaying a baseline, 888
displaying unsynchronized signal, 888
divide math function, 326, 347
DNS IP, 52
domain, 52
domain, network printer, 367
driver, printer, 1065
DSO models, 6
duplicate mnemonics, 1143
duration, 922, 923, 926
duration for glitch trigger, 909, 910, 914
duration of power analysis, 567, 568, 569
,
570, 571, 572
duration qualifier, trigger, 922, 923
duration triggering, 878
duty cycle measurement, 61, 406, 424
Duty Cycle, power modulation analysis, 552
DVM commands, 309
DVM displayed value, 311
DVM enable/disable, 312
DVM frequency value, 313
DVM input source, 315
DVM mode, 314
E
EBURst trigger commands, 896
ECL channel threshold, 1051
ECL threshold voltage for digital channels, 295
ECL trigger threshold voltage, 1094
edge activity, 1049
edge counter, Edge Then Edge trigger, 893
edge counter, Nth edge of burst, 897
edge coupling, 902
edge fall time, 425
edge parameter for delay measurement, 416
edge preshoot measured, 436
edge rise time, 441
EDGE SEARch commands, 782
edge search slope, 783
edge search source, 784
edge slope, 905
edge source, 906
edge string for OR'ed edge trigger, 917
EDGE trigger commands, 901
edge triggering, 878
edges (activity) on digital channels, 191
edges in measurement, 414
efficiency, 476
efficiency power analysis, apply, 535
elapsed time in mask test, 502
ellipsis, 158
enable channel labels, 305
enabling calibration, 256
enabling channel display, 266
enabling status register bits, 166, 180
end of string (EOS) terminator, 1140
end of text (EOT) terminator, 1140
end or identify (EOI)
, 1140
energy loss, 477
EOI (end or identify), 1140
EOS (end of string) terminator, 1140
EOT (end of text) terminator, 1140
erase data, 303
erase measurements, 1067
erase screen, 1057
error counter (ARINC 429), 638
error counter (ARINC 429), reset, 639
error frame count (CAN), 654
error frame count (UART), 760
error messages, 855, 1097
error number, 855
error queue, 855, 1117
error, measurement, 406
ESB (Event Status Bit), 181, 183
ESE (Standard Event Status Enable
Register), 166, 1116
ESR (Standard Event Status Register), 168,
1115
ETE demo signal, 283
event status conditions occurred, 183
Event Status Enable Register (ESE), 166, 1116
Event Status Register (ESR), 168, 224, 1115
example code, :ACQuire:COMPlete, 229
example code, :ACQuire:SEGMented, 235
example code, :ACQuire:TYPE, 240
example code, :AUToscale, 194
example code, :CHANnel<n>:LABel, 269
example code, :CHANnel<n>:PROBe, 271
example code, :CHANnel<n>:RANGe, 277
example code, :DIGitize, 200
example code, :DISPlay:DATA, 304
example code, :DISPlay:LABel, 305
example code, :DISPlay:ORDer, 1056
example code, :MEASure:PERiod, 445
example code, :MEASure:RESults, 438
example code, :MEASure:TEDGe, 453
example code, :MTESt, 491
example code, :POD<n>:THReshold, 527
example code, :RUN/:STOP, 219
example code, :SYSTem:SETup, 862
example code, :TIMebase:DELay, 1093
example code, :TIMebase:MODE, 867
example code, :TIMebase:RANGe, 869
example code, :TIMebase:REFerence, 870
example code, :TRIGger:MODE, 886
example code, :TRIGger:SLOPe, 905
example code, :TRIGger:SOURce, 906
example code, :VIEW and :BLANk, 225
example code, :WAVeform, 982
example code, :WAVeform:DATA, 969
example code, :WAVeform:POINts, 973
example code, :WAVeform:PREamble, 977
example code, :WAVeform:SEGMented, 235
example code, *RST, 178
example programs, 6, 1147
EXE (Execution Error) status bit, 166, 168
execution error detected in Standard Event
Status, 168
exponential fall waveform generator
output, 1008
exponential math function, 327, 347
exponential notation, 157
exponential rise waveform generator
output, 1008
extended video triggering license, 948
external glitch trigger source, 915
external range, 320
external trigger, 317, 319, 906
EXTernal trigger commands, 317
EXTernal trigger level, 903
external trigger probe attenuation factor, 319
external trigger probe sensing, 1058
EXTernal trigger source, 906
external trigger units, 321
F
fail count, current harmonics analysis, 540
fail/pass status (overall) for current harmonics
analysis, 545
failed waveforms in mask test, 500
failure, self test, 185
fall time measurement, 406, 425

Agilent Technologies InfiniiVision 3000 X-Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 3000 X-Series
Category	Test Equipment
Language	English