Agilent Technologies InfiniiVision 3000 X-Series Programmer's Guide

Index
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide 1271
Fall Time, power modulation analysis, 552
falling edge count measurement, 427
falling pulse count measurement, 428
Fast Fourier Transform (FFT) functions, 326,
334, 335, 337, 1059
FF values in waveform data, 969
FFT (Fast Fourier Transform) functions, 326,
334, 335, 337, 1059
FFT (Fast Fourier Transform) operation, 347,
981
FFT vertical units, 336
fifty ohm impedance, disable setting, 861
filename for hardcopy, 1062
filename for recall, 600, 1006
filename for save, 609
filter for frequency reject, 904
filter for high frequency reject, 881
filter for noise reject, 887
filter used to limit bandwidth, 264, 318
filters to Fast Fourier Transforms, 337
filters, math, 327
fine horizontal adjustment (vernier), 872
fine vertical adjustment (vernier), 280
finish pending device operations, 172
first point displayed, 991
FLATtop window for amplitude
measurements, 337
FLEXray autoset for event trigger, 681
FLEXray autosetup, 671
FlexRay demo signal, 284
FlexRay frame counters, reset, 675
FLEXray SEARch commands, 814
FlexRay serial search, cycle, 815
FlexRay serial search, data, 816
FlexRay serial search, data length, 817
FlexRay serial search, frame, 818
FlexRay serial search, mode, 819
FLEXray source, 678
FLEXray trigger, 679
FLEXray trigger commands, 669
FM burst demo signal, 283
FM modulation type, waveform
generator, 1023
force trigger, 880
format, 971, 976
format (word), ARINC 429, 641
format for block data, 171
format for generic video, 944, 948
format for hardcopy, 1061
format for image, 612
format for waveform data, 622
FormattedIO488 object, 63
formfeed for hardcopy, 358, 362
formulas for data conversion, 964
frame, 745
frame counters (CAN), error, 654
frame counters (CAN), overload, 655
frame counters (CAN), reset, 656
frame counters (CAN), total, 657
frame counters (FlexRay), null, 674, 676
frame counters (FlexRay), reset, 675
frame counters (FlexRay), total,
677
frame counters (UART), error, 760
frame counters (UART), reset, 761
frame counters (UART), Rx frames, 762
frame counters (UART), Tx frames, 763
frame ID, FLEXray BSS event trigger, 682
frame ID, FLEXray frame trigger, 686
frame type, FLEXray frame trigger, 687
framing, 743
frequency deviation, waveform generator FM
modulation, 1015
frequency measurement, 61, 406, 426
frequency measurements with X cursors, 387
frequency resolution, 337
frequency span of display, 335
frequency versus dB, 326
Frequency, power modulation analysis, 552
front panel mode, 888
front panel Single key, 221
front panel Stop key, 223
front-panel lock, 856
FSK modulation type, waveform
generator, 1023
FSK rate, waveform generator
modulation, 1018
full-scale horizontal time, 869, 874
full-scale vertical axis defined, 349
function, 225, 333, 334, 335, 337, 346, 347,
349, 350, 351,
1059, 1060
FUNCtion commands, 323
function memory, 222
function turned on or off, 1060
function, demo signal, 282
function, first source input, 352
function, second source input, 354
function, waveform generator, 1007
functions, 981
G
g(t) source, first input channel, 341
g(t) source, math operation, 340
g(t) source, second input channel, 342
gain for Ax + B math operation, 344
gateway IP, 52
gaussian pulse waveform generator
output, 1009
general SBUS<n> commands, 631
general SEARch commands, 778
general trigger commands, 879
GENeric, 944, 948
generic video format, 944, 948
Generic video trigger, edge number, 949
Generic video trigger, greater than sync pulse
width time, 952
Generic video trigger, horizontal sync
control, 950
Generic video trigger, horizontal sync pulse
time, 951
glitch demo signal, 282
glitch duration, 914
glitch qualifier, 913
GLITch SEARch commands, 785
glitch search, greater than value, 786
glitch search, less than value, 787
glitch search, polarity, 788
glitch search, qualifier, 789
glitch search, range, 790
glitch search, source, 791
glitch source, 915
GLITch trigger commands, 907
glitch trigger duration, 909
glitch trigger polarity, 912
glitch trigger source, 909
GPIB interface,
51, 52
graticule area for hardcopy print, 359
graticule colors, invert for hardcopy, 363, 1064
graticule colors, invert for image, 613
grayscale palette for hardcopy, 371
grayscale palette for image, 614
grayscaling on hardcopy, 1063
greater than qualifier, 913
greater than time, 909, 914, 922, 926
greater than value for glitch search, 786
groups of digital channels, 523, 525, 527,
1051
H
HANNing window for frequency
resolution, 337
hardcopy, 215, 358
HARDcopy commands, 357
hardcopy factors, 361, 611
hardcopy filename, 1062
hardcopy format, 1061
hardcopy formfeed, 362
hardcopy grayscale, 1063
hardcopy invert graticule colors, 363, 1064
hardcopy layout, 364
hardcopy palette, 371
hardcopy print, area, 359
hardcopy printer driver, 1065
head type, probe, 272
header, 1139
high pass filter math function, 327
high resolution acquisition type, 963
high trigger level, 884
high-frequency reject filter, 881, 904
high-level voltage, waveform generator, 1030
high-pass filter cutoff frequency, 338
high-pass filter math function, 347
high-resolution acquisition type, 228
hold time, setup and hold trigger, 936
hold until operation complete, 172
holdoff time, 882
holes in waveform data, 969
hop frequency, waveform generator FSK
modulation, 1017
horizontal adjustment, fine (vernier), 872
horizontal position,
873
horizontal scale, 871, 875
horizontal scaling, 976
horizontal time, 869, 874, 1068
Host name softkey, 52

Agilent Technologies InfiniiVision 3000 X-Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 3000 X-Series
Category	Test Equipment
Language	English