Agilent Technologies InfiniiVision 3000 X-Series Programmer's Guide

1272 Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
Index
hostname, 52
I
I1080L50HZ, 944, 948
I1080L60HZ, 944, 948
I2C demo signal, 283
I2S alignment, 690
I2S audio channel, 699
I2S clock slope, 692
I2S CLOCk source, 694
I2S DATA source, 695
I2S demo signal, 284
I2S pattern data, 700
I2S pattern format, 702
I2S range, 703
I2S receiver width, 693
I2S SEARch commands, 820
I2S serial bus commands, 688
I2S serial decode base, 691
I2S serial search, audio channel, 821
I2S serial search, data, 823
I2S serial search, format, 824
I2S serial search, mode, 822
I2S serial search, range, 825
I2S transmit word size, 705
I2S trigger operator, 697
I2S triggering, 629
I2S word select (WS) low, 706
I2S word select (WS) source, 696
id mode, 668
ID pattern, CAN trigger, 667
identification number, 170
identification of options, 173
identifier, LIN, 726
idle, 898
idle until operation complete
, 172
IDN (Identification Number), 170
IEC 61000-3-2 standard for current harmonics
analysis, 544
IEEE 488.2 standard, 163
IIC address, 711
IIC clock, 709
IIC data, 710, 712
IIC data 2, 713
IIC SEARch commands, 826
IIC serial decode address field size, 708
IIC serial search, address, 829
IIC serial search, data, 830
IIC serial search, data2, 831
IIC serial search, mode, 827
IIC serial search, qualifier, 832
IIC trigger commands, 707
IIC trigger qualifier, 714
IIC trigger type, 715
IIC triggering, 630
image format, 612
image invert graticule colors, 613
image memory, 222
image palette, 614
image, save, 610
image, save with inksaver, 613
impedance, 267
infinity representation, 1145
initial load current, transient response
analysis, 593
initialization, 60, 63
initialize, 176, 858
initialize label list, 306
initiate acquisition, 199
inksaver, save image with, 613
input coupling for channels, 265
input for integrate, DC offset correction, 343
input impedance for channels, 267, 1053
input inversion for specified channel, 268
input power, 479
inrush current, 483
inrush current analysis, 547, 548, 549
inrush current expected, 573
insert label, 269
installed options identified, 173
instruction header, 1139
instrument number, 170
instrument options identified, 173
instrument requests service, 183
instrument serial number, 220
instrument settings, 358
instrument status, 70
instrument type, 170
integrate DC offset correction, 343
integrate math function, 326, 347, 981
INTegrate source for function, 1059
internal low-pass filter, 264, 318
introduction to :ACQuire commands, 227
introduction to :BUS<n> commands, 242
introduction to :CALibrate commands, 251
introduction to :CHANnel<n> commands, 263
introduction to :DEMO commands,
281
introduction to :DIGital<d> commands, 290
introduction to :DISPlay commands, 298
introduction to :EXTernal commands, 317
introduction to :FUNCtion commands, 326
introduction to :HARDcopy commands, 358
introduction to :LISTer commands, 375
introduction to :MARKer commands, 380
introduction to :MEASure commands, 406
introduction to :POD<n> commands, 523
introduction to :RECall commands, 598
introduction to :SAVE commands, 607
introduction to :SBUS commands, 629
introduction to :SYSTem commands, 852
introduction to :TIMebase commands, 866
introduction to :TRIGger commands, 877
introduction to :WAVeform commands, 961
introduction to :WGEN commands, 998
introduction to :WMEMory<r>
commands, 1033
introduction to common (*) commands, 163
introduction to root (:) commands, 190
invert graticule colors for hardcopy, 363, 1064
invert graticule colors for image, 613
inverted masks, bind levels, 516
inverting input for channels, 268
IO library, referencing, 62
IP address, 52
IronPython, SCPI.NET example, 1260
K
key disable, 856
key press detected in Standard Event Status
Register, 168
knob disable, 856
known state, 176, 858
L
label, 1050
label command, bus, 248
label list, 269, 306
label reference waveforms, 1037
label, ARINC 429 trigger, 645, 649, 803
label, digital channel, 292
labels, 269, 305, 306
labels to store calibration information, 254
labels, specifying, 298
LAN interface, 51, 54
LAN Settings softkey, 52
landscape layout for hardcopy, 364
language for program examples, 59
layout for hardcopy, 364
leakage into peak spectrum, 337
learn string, 171, 862
least significant byte first, 967
left reference, 870
legal values for channel offset, 270
legal values for frequency span, 335
legal values for offset, 346, 350
length for waveform data, 623
less than qualifier, 913
less than time, 910, 914, 923, 926
less than value for glitch search, 787
level for trigger voltage, 903
, 911
LF coupling, 902
license information, 173
limits for line number, 944
LIN acknowledge, 720
LIN baud rate, 721
LIN demo signal, 283
LIN identifier, 726
LIN pattern data, 727
LIN pattern format, 730
LIN SEARch commands, 833
LIN serial decode bus parity bits, 719
LIN serial search, data, 836
LIN serial search, data format, 838
LIN serial search, data length, 837
LIN serial search, frame ID, 834
LIN serial search, mode, 835
LIN source, 722
LIN standard, 723
LIN sync break, 724
LIN trigger, 725, 729
LIN trigger commands, 717
LIN trigger definition, 1091

Agilent Technologies InfiniiVision 3000 X-Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 3000 X-Series
Category	Test Equipment
Language	English