Agilent Technologies InfiniiVision 3000 X-Series Programmer's Guide

1274 Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
Index
message displayed, 183
message error, 1097
message queue, 1114
messages ready, 183
midpoint of thresholds, 433
MIL-STD-1553 demo signal, 284
MIL-STD-1553 serial decode base, 733
MIL-STD-1553 serial search, data, 841
MIL-STD-1553 serial search, mode, 840
MIL-STD-1553 serial search, Remote Terminal
Address, 842
MIL-STD-1553, dual demo signal, 284
minimum duration, 909, 922, 923, 926
minimum vertical value measurement, 460
minimum vertical value, time of, 468, 1071
MISO data pattern width, 749
MISO data pattern, SPI trigger, 748
MISO data source, SPI trigger, 746
MISO data, SPI, 985
mixed-signal demo signals, 283
mixed-signal oscilloscopes, 6
mnemonics, duplicate, 1143
mode, 381, 867, 945
mode, serial decode, 633
model number, 170
models, oscilloscope, 3
modes for triggering, 886
Modify softkey, 52
modulating signal frequency, waveform
generator, 1014, 1016
modulation (waveform generator),
enabling/disabling, 1022
modulation analysis, 550
modulation analysis source (voltage or
current), 551
modulation analysis, type of, 552
modulation type, waveform generator, 1023
MOSI data pattern width, 751
MOSI data pattern, SPI trigger, 750
MOSI data source, SPI trigger, 747, 1092
most significant byte first, 967
move cursors, 1072, 1073
msbfirst, 967
MSG (Message), 181, 183
MSO models, 6
MSS (Master Summary Status), 183
MTEenable (Mask Test Event Enable
Register), 201
MTERegister[:EVENt] (Mask Test Event Event
Register), 203, 1122
MTESt commands, 489
multi-channel waveform data, save, 617
multiple commands, 1143
multiple queries, 69
multiply math function, 326, 347, 981
multiply math function as g(t) source, 340
N
N2820A high sensitivity current probe, 32, 418,
419, 420, 421, 422, 423
N8900A InfiniiView oscilloscope analysis
software, 617
name channels, 269
name list, 306
natural logarithm math function, 327
negative glitch trigger polarity, 912
negative pulse width, 429
negative pulse width measurement, 61
negative pulse width, power modulation
analysis, 552
negative slope, 741, 905
negative slope, Nth edge in burst, 899
negative TV trigger polarity, 946
network domain password, 368
network domain user name, 370
network printer address, 365
network printer domain, 367
network printer slot, 369
network printer, apply connection settings, 366
new line (NL) terminator, 157, 1140
new load current, transient response
analysis, 594
NL (new line) terminator, 157, 1140
noise floor, 587, 590
noise reject filter, 887
noise waveform generator output, 1008
noise, adding to waveform generator
output,
1021
noisy sine waveform demo signal, 282
non-core commands, 1138
non-interlaced GENeric mode, 948
non-volatile memory, label list, 248, 292, 306
normal acquisition type, 227, 962
normal trigger sweep mode, 877
notices, 2
NR1 number format, 157
NR3 number format, 157
Nth edge burst trigger source, 900
Nth edge burst triggering, 878
Nth edge in a burst idle, 898
Nth edge in burst slope, 899
Nth edge of burst counter, 897
Nth edge of Edge Then Edge trigger, 893
NTSC, 944, 948
null frame count (FlexRay), 674
null offset, 587
NULL string, 854
number format, 157
number of points, 232, 972, 974
number of time buckets, 972, 974
numeric variables, 68
numeric variables, reading query results into
multiple, 70
nwidth, 429
O
obsolete and discontinued commands, 1043
obsolete commands, 1138
occurrence reported by magnitude, 1074
offset, 327
offset for Ax + B math operation, 345
offset value for channel voltage, 270
offset value for selected function, 346, 350
offset, waveform generator, 1032
one values in waveform data, 969
OPC (Operation Complete) command, 172
OPC (Operation Complete) status bit, 166, 168
OPEE (Operation Status Enable Register), 205
Open method, 63
operating configuration, 171, 862
operating state, 179
operation complete, 172
operation status condition register, 207
Operation Status Condition Register
(:OPERegister:CONDition), 207, 1119
operation status conditions occurred, 183
Operation Status Enable Register (OPEE), 205
operation status event register, 209
Operation Status Event Register
(:OPERegister[:EVENt]), 209, 1118
operations for function, 347
operators, math, 326
OPERegister:CONDition (Operation Status
Condition Register), 207, 1119
OPERegister[:EVENt] (Operation Status Event
Register), 209, 1118
OPT (Option Identification),
173
optional syntax terms, 157
options, 173
OR trigger commands, 916
order of digital channels on display, 1056
order of output, 967
oscilloscope connection, opening, 63
oscilloscope connection, verifying, 53
oscilloscope external trigger, 317
oscilloscope models, 3
oscilloscope rate, 238
oscilloscope, connecting, 51
oscilloscope, initialization, 60
oscilloscope, operation, 6
oscilloscope, program structure, 60
oscilloscope, setting up, 51
oscilloscope, setup, 64
output control, demo signals, 287
output control, waveform generator, 1025
output load impedance, waveform
generator, 1026
output messages ready, 183
output power, 482
output queue, 172, 1113
output queue clear, 165
output ripple, 487
output ripple analysis, 563
output sequence, 967
overall pass/fail status for current harmonics
analysis, 545
overlapped commands, 1146
overload, 276
Overload Event Enable Register (OVL), 211
Overload Event Register (:OVLRegister),
1121
Overload Event Register (OVLR), 213
overload frame count (CAN), 655
overload protection, 211, 213

Agilent Technologies InfiniiVision 3000 X-Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 3000 X-Series
Category	Test Equipment
Language	English