EasyManuals Logo

Agilent Technologies InfiniiVision 3000 X-Series Programmer's Guide

Agilent Technologies InfiniiVision 3000 X-Series
1282 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1276 background imageLoading...
Page #1276 background image
1276 Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
Index
query subsystem, 242, 290
querying setup, 263
querying the subsystem, 878
queues, clearing, 1124
quick reference, commands, 73
quoted ASCII string, 158
QYE (Query Error) status bit, 166, 168
R
ramp symmetry, waveform generator, 1011
ramp symmetry, waveform generator
modulating signal, 1020
ramp waveform generator output, 1007
range, 327, 874
range for channels, 277
range for duration trigger, 926
range for external trigger, 320
range for full-scale vertical axis, 349
range for glitch search, 790
range for glitch trigger, 914
range for time base, 869
range of offset values, 270
range qualifier, 913
range, I2S, 703
ranges, value, 158
rate, 238
ratio measurements with X cursors, 387
ratio measurements with Y cursors, 392
ratio of AC RMS values measured between
channels, 462
Ratio, power modulation analysis, 552
raw acquisition record, 974
RCL (Recall), 175
Rds (dynamic ON resistance) waveform, 586
Rds(on) value for conduction calculation, 588
reactive power, 485, 562
read configuration, 171
ReadIEEEBlock method, 63, 67, 69
ReadList method, 63, 67
ReadNumber method,
63, 67
readout, 1068
ReadString method, 63, 67
real (actual) power, 562
real power, 486
real-time acquisition mode, 231
recall, 175, 598, 862
recall arbitrary waveform, 599
RECall commands, 597
recall filename, 600, 1006
recall mask, 601
recall path information, 602
recall reference waveform, 604
recall setup, 603
recalling and saving data, 298
receiver width, I2S, 693
RECTangular window for transient signals, 337
reference, 327, 870
reference for time base, 1093
reference waveform save source, 626
reference waveform, recall, 604
reference waveform, save, 627
reference waveforms, clear, 1035
reference waveforms, display, 1036
reference waveforms, label, 1037
reference waveforms, save to, 1038
reference waveforms, skew, 1039
reference waveforms, Y offset, 1040
reference waveforms, Y range, 1041
reference waveforms, Y scale, 1042
reference, lister, 378
registers, 168, 175, 179, 192, 201, 203, 205,
207, 209, 211, 213, 216, 218
registers, clearing, 1124
reject filter, 904
reject high frequency, 881
reject noise, 887
relative standard deviation, 451
remote control examples, 1147
Remote Terminal Address (RTA), M1553
trigger, 736
remove cursor information, 381
remove labels, 305
remove message from display, 854
reorder channels, 193
repetitive acquisitions, 219
report errors, 855
report transition, 452, 454
reporting status, 1105
reporting the setup, 878
request service, 183
Request-for-OPC flag clear, 165
reset, 176
reset conditions, 176
reset defauts, waveform generator, 1028
reset mask statistics, 501
reset measurements, 303
resolution of printed copy, 1063
resource session object, 63
ResourceManager object, 63
restore configurations, 171, 175, 179, 862
restore labels, 305
restore setup, 175
return values, query, 1145
returning acquisition type, 239
returning number of data points, 232
RF burst demo signal, 283
right reference, 870
ringing pulse demo signal, 282
ripple (output) analysis, 563
ripple, output, 487
rise time measurement, 406
rise time of positive edge, 441
Rise Time, power modulation analysis, 552
rising edge count measurement, 432
rising pulse count measurement, 435
RMS - AC, power modulation analysis, 552
RMS value measurement, 423, 463
roll time base mode, 867
root (:) commands, 187, 190
root level commands, 3
RQL (Request Control) status bit, 166, 168
RQS (Request Service), 183
RS-232/UART triggering, 630
RST (Reset), 176
rules, tree traversal, 1143
rules, truncation, 1140
run, 184, 219
Run bit, 207, 209
run count, current harmonics analysis, 543
run mode, mask test, 508
running configuration, 179, 862
RUNT SEARch commands, 792
runt search polarity, 793
runt search qualifier, 794
runt search source, 795
runt search, pulse time, 796
RUNT trigger commands, 927
runt trigger polarity, 928
runt trigger qualifier, 929
runt trigger source, 930
runt trigger time, 931
Rx frame count (UART), 762
Rx source, 767
S
sample rate, 238
sampled data, 1055
sampled data points, 969
SAV (Save), 179
save, 179, 607
save arbitrary waveform, 608
SAVE commands, 605
save current harmonics analysis results, 618
save filename, 609
save image, 610
save image with inksaver, 613
save mask, 615, 616
save mask test failures, 511
save path information, 619
save reference waveform, 627
save setup, 620
save to reference waveform location, 1038
save waveform data, 621
saved image, area, 1090
saving and recalling data, 298
SBUS A429 commands, 634
SBUS CAN commands, 652
SBUS commands, 629
SBUS I2S commands, 688
SBUS<n> commands, general, 631
scale, 351, 871, 875
scale factors output on hardcopy, 361, 611
scale for channels, 278
scale units for channels, 279
scale units for external trigger, 321
scaling display factors
, 271
SCPI commands, 71
SCPI.NET example in C#, 1248
SCPI.NET example in IronPython, 1260
SCPI.NET example in Visual Basic .NET, 1254
SCPI.NET examples, 1248
scratch measurements, 1067
screen area for hardcopy print, 359
screen area for saved image, 1090

Table of Contents

Other manuals for Agilent Technologies InfiniiVision 3000 X-Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Agilent Technologies InfiniiVision 3000 X-Series and is the answer not in the manual?

Agilent Technologies InfiniiVision 3000 X-Series Specifications

General IconGeneral
BrandAgilent Technologies
ModelInfiniiVision 3000 X-Series
CategoryTest Equipment
LanguageEnglish

Related product manuals