Agilent Technologies InfiniiVision 3000 X-Series Programmer's Guide

Index
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide 1277
screen image data, 304
SDI pattern, ARINC 429 trigger, 647, 806
SEARch commands, 777
SEARch commands, A429, 802
SEARch commands, CAN, 808
SEARch commands, EDGE, 782
SEARch commands, FLEXray, 814
SEARch commands, general, 778
SEARch commands, GLITch, 785
SEARch commands, I2S, 820
SEARch commands, IIC, 826
SEARch commands, LIN, 833
SEARch commands, M1553, 839
SEARch commands, RUNT, 792
SEARch commands, SPI, 843
SEARch commands, TRANsition, 797
SEARch commands, UART, 847
search mode, 780
search state, 781
search, edge slope, 783
search, edge source, 784
SECAM, 944, 948
seconds per division, 871
segmented waveform save option, 625
segments, analyze, 233
segments, count of waveform, 979
segments, setting number of memory, 234
segments, setting the index, 235
segments, time tag, 980
select measurement channel, 444
self-test, 185
sensing a channel probe, 1054
sensing a external trigger probe
, 1058
sensitivity of oscilloscope input, 271
sequential commands, 1146
serial clock, 709, 744
serial data, 710
serial decode bus, 629
serial decode bus display, 632
serial decode mode, 633
serial frame, 745
serial number, 220
service request, 183
Service Request Enable Register (SRE), 181,
1111
set center frequency, 334
set cursors, 1072, 1073
set date, 853
set time, 864
set up oscilloscope, 51
setting digital display, 291
setting digital label, 248, 292
setting digital position, 293
setting digital threshold, 295
setting display, 333
setting external trigger level, 317
setting impedance for channels, 267
setting inversion for channels, 268
setting pod display, 525
setting pod size, 526
setting pod threshold, 527
settings, 175, 179
settings, instrument, 358
setup
, 228, 242, 263, 290, 298, 358, 862
setup and hold trigger clock source, 934
setup and hold trigger data source, 935
setup and hold trigger hold time, 936
setup and hold trigger setup time, 937
setup and hold trigger slope, 933
setup configuration, 175, 179, 862
setup defaults, 176, 858
setup memory, 175
setup reported, 878
setup time, setup and hold trigger, 937
setup, recall, 603
setup, save, 620
shape of modulation signal, waveform
generator, 1019
SHOLd trigger commands, 932
short form, 5, 1140
show channel labels, 305
show measurements, 406, 443
SICL example in C, 1228
SICL example in Visual Basic, 1237
SICL examples, 1228
sigma, mask test run, 513
signal speed, ARINC 429, 644
signal type, 275
signal type, ARINC 429
, 642
signed data, 965
simple command headers, 1141
sine cardinal waveform generator output, 1008
sine waveform demo signal, 282
sine waveform generator output, 1007
single acquisition, 221
single-ended probe heads, 272
single-ended signal type, 275
single-shot demo signal, 282
single-shot DUT, synchronizing with, 1132
size, 526
size, digital channels, 294
skew, 274, 1052
skew reference waveform, 1039
slew rate power analysis, 583
slope, 741, 905
slope (direction) of waveform, 1074
slope not valid in TV trigger mode, 905
slope parameter for delay measurement, 416
slope, arming edge, Edge Then Edge
trigger, 890
slope, Nth edge in burst, 899
slope, setup and hold trigger, 933
slope, transition search, 799
slope, transition trigger, 940
slope, trigger edge, Edge Then Edge
trigger, 894
slot, network printer, 369
smoothing acquisition type, 963
snapshot all measurement, 408
software version, 170
source, 444, 643, 662, 722
source (voltage or current) for slew rate
analysis, 584
source channel, M1553, 734
source for function, 1059
source for glitch search, 791
source for Nth edge burst trigger, 900
source for trigger, 906
source for TV trigger, 947
source input for function, first, 352
source input for function, second, 354
source, arming edge, Edge Then Edge
trigger, 891
source, automask, 496
source, FLEXray, 678
source, mask test, 521
source, runt search, 795
source, runt trigger, 930
source, save reference waveform, 626
source, transition trigger, 800, 941
source, trigger edge, Edge Then Edge
trigger, 895
source, waveform, 981
span, 326
span of frequency on display, 335
specify measurement, 444
speed of ARINC 429 signal, 644
SPI, 741
SPI clock timeout, 742
SPI decode bit order, 740
SPI decode word width, 753
SPI demo signal, 284
SPI MISO data
, 985
SPI SEARch commands, 843
SPI serial search, data, 845
SPI serial search, data width, 846
SPI serial search, mode, 844
SPI trigger, 743, 749, 751
SPI trigger clock, 744
SPI trigger commands, 738
SPI trigger frame, 745
SPI trigger MISO data pattern, 748
SPI trigger MOSI data pattern, 750
SPI trigger type, 752
SPI trigger, MISO data source, 746
SPI trigger, MOSI data source, 747, 1092
SPI triggering, 630
square math function, 327, 347
square root math function, 326, 347
square wave duty cycle, waveform
generator, 1012
square waveform generator output, 1007
SRE (Service Request Enable Register), 181,
1111
SRQ (Service Request interrupt), 201, 205, 216
SSM pattern, ARINC 429 trigger, 648, 807
standard deviation measured on
waveform, 442
Standard Event Status Enable Register
(ESE), 166, 1116
Standard Event Status Register (ESR), 168,
1115
standard for video, 948
standard, LIN, 723
start acquisition, 184, 199, 219, 221
start and stop edges, 414

Agilent Technologies InfiniiVision 3000 X-Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 3000 X-Series
Category	Test Equipment
Language	English