Agilent Technologies InfiniiVision 3000 X-Series Programmer's Guide

1278 Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide
Index
start cursor, 1072
start measurement, 406
start print job, 373
start time, 914, 1072
start time marker, 1069
state memory, 179
state of instrument, 171, 862
statistics increment, 448
statistics reset, 450
statistics results, 438
statistics, max count, 449
statistics, relative standard deviation, 451
statistics, type of, 446
status, 182, 222, 224
Status Byte Register (STB), 180, 182, 183,
1109
status data structure clear, 165
status registers, 70
status reporting, 1105
STB (Status Byte Register), 180, 182, 183,
1109
steady state output voltage expected, 578,
579, 580
step size for frequency span, 335
stop, 199, 223
stop acquisition, 223
stop cursor, 1073
stop displaying channel, 198
stop displaying math function, 198
stop displaying pod, 198
stop on mask test failure, 512
stop time, 914, 1073
storage, 179
store instrument setup, 171, 179
store setup, 179
storing calibration information, 254
string variables, 68
string variables, reading multiple query results
into, 69
string variables, reading query results into
multiple, 69
string, quoted ASCII, 158
subnet mask, 52
subsource, waveform source, 985
subsystem commands, 3, 1143
subtract math function, 326, 347, 981
subtract math function as g(t) source, 340
sweep mode, trigger, 877, 888
sweep speed set to fast to measure fall
time, 425
sweep speed set to fast to measure rise
time, 441
switch disable, 856
switching level, current, 587
switching level, voltage, 590
switching loss per cycle, 474
switching loss power analysis, 585
sync break, LIN, 724
sync frame count (FlexRay), 676
syntax elements, 157
syntax rules, program data, 1142
syntax, optional terms, 157
syntax, program message, 1139
SYSTem commands, 851
system commands, 853, 854, 855, 856, 862,
864
system commands introduction, 852
T
table of current harmonics results, 539
tdelta, 1068
tedge, 452
telnet ports 5024 and 5025, 969
Telnet sockets, 71
temporary message, 854
TER (Trigger Event Register), 224, 1112
termination conditions, mask test, 508
test sigma, mask test run, 513
test, self, 185
text, writing to display, 854
THD (total harmonics distortion), 546
threshold, 295, 527, 1051, 1094
threshold voltage (lower) for
measurement, 1066
threshold voltage (upper) for
measurement, 1076
thresholds, 414, 1069
thresholds used to measure period, 433
thresholds, how autoscale affects, 193
time base, 867, 868, 869, 870, 871, 1093
time base commands introduction, 866
time base reset conditions, 177, 859
time base window, 873, 874, 875
time between points, 1068
time buckets, 229
, 230
time delay, 1093
time delay, Edge Then Edge trigger, 892
time delta, 1068
time difference between data points, 989
time duration, 914, 922, 923, 926
time holdoff for trigger, 882
time interval, 452, 454, 1068
time interval between trigger and
occurrence, 1074
time marker sets start time, 1069
time measurements with X cursors, 387
time per division, 869
time record, 337
time reference, lister, 378
time specified, 464
time, calibration, 260
time, mask test run, 514
time, runt pulse search, 796
time, runt trigger, 931
time, start marker, 1072
time, stop marker, 1073
time, system, 864
time, transition search, 801
time, transition trigger, 942
time/div, how autoscale affects, 193
time-at-max measurement, 1070
time-at-min measurement, 1071
TIMebase commands, 865
timebase vernier, 872
TIMebase:MODE, 66
time-ordered label list
, 306
timeout, SPI clock, 742
timing measurement, 406
title channels, 269
title, mask test, 522
tolerance, automask, 498, 499
top of waveform value measured, 465
total frame count (CAN), 657
total frame count (FlexRay), 677
total harmonics distortion (THD), 546
total waveforms in mask test, 503
trace memory, 222
track measurements, 443
trademarks, 2
transfer instrument state, 171, 862
transforms, math, 326
transient response, 488
transient response analysis, 591, 592, 595
TRANsition SEARch commands, 797
transition search qualifier, 798
transition search slope, 799
transition search time, 801
transition trigger qualifier, 939
transition trigger slope, 940
transition trigger source, 800, 941
transition trigger time, 942
transmit word size, I2S, 705
tree traversal rules, 1143
trend measurement, 355
TRG (Trigger), 181, 183
, 184
TRIG OUT BNC, 255
trigger armed event register, 207, 209
trigger burst, UART, 770
trigger channel source, 915, 947
TRIGger commands, 877
TRIGger commands, general, 879
trigger data, UART, 771
TRIGger DELay commands, 889
trigger duration, 922, 923
TRIGger EBURst commands, 896
TRIGger EDGE commands, 901
trigger edge coupling, 902
trigger edge slope, 905
trigger edge slope, Edge Then Edge
trigger, 894
trigger edge source, Edge Then Edge
trigger, 895
trigger event bit, 224
Trigger Event Register (TER), 1112
TRIGger FLEXray commands, 669
TRIGger GLITch commands, 907
trigger holdoff, 882
trigger idle, UART, 772
TRIGger IIC commands, 707
trigger level auto set up, 883
trigger level constants, 271
trigger level voltage, 903
trigger level, high, 884
trigger level, low, 885
TRIGger LIN commands, 717

Agilent Technologies InfiniiVision 3000 X-Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 3000 X-Series
Category	Test Equipment
Language	English