Agilent Technologies InfiniiVision 3000 X-Series Programmer's Guide

Index
Agilent InfiniiVision 3000 X-Series Oscilloscopes Programmer's Guide 1279
TRIGger M1553 commands, 731
trigger occurred, 183
TRIGger OR commands, 916
TRIGger PATTern commands, 918
trigger pattern qualifier, 924
trigger qualifier, UART, 773
trigger reset conditions, 177, 859
TRIGger RUNT commands, 927
TRIGger SHOLd commands, 932
trigger SPI clock slope, 741
TRIGger SPI commands, 738
trigger status bit, 224
trigger sweep mode, 877
TRIGger TV commands, 938, 943
trigger type, ARINC 429, 650, 804
trigger type, SPI, 752
trigger type, UART, 774
TRIGger UART commands, 754
TRIGger USB commands, 953
trigger, ARINC 429 source, 643
trigger, CAN, 663
trigger, CAN pattern data length, 666
trigger, CAN pattern ID mode, 668
trigger, CAN sample point, 659
trigger, CAN signal baudrate, 660
trigger, CAN signal definition, 661
trigger, CAN source, 662
trigger, duration greater than, 922
trigger, duration less than, 923
trigger, duration range, 926
trigger, edge coupling, 902
trigger, edge level
, 903
trigger, edge reject, 904
trigger, edge slope, 905
trigger, edge source, 906
trigger, FLEXray, 679
trigger, FLEXray error, 680
trigger, FLEXray event, 683
trigger, force a, 880
trigger, glitch greater than, 909
trigger, glitch less than, 910
trigger, glitch level, 911
trigger, glitch polarity, 912
trigger, glitch qualifier, 913
trigger, glitch range, 914
trigger, glitch source, 915
trigger, high frequency reject filter, 881
trigger, holdoff, 882
trigger, I2S, 697
trigger, I2S alignment, 690
trigger, I2S audio channel, 699
trigger, I2S clock slope, 692
trigger, I2S CLOCksource, 694
trigger, I2S DATA source, 695
trigger, I2S pattern data, 700
trigger, I2S pattern format, 702
trigger, I2S range, 703
trigger, I2S receiver width, 693
trigger, I2S transmit word size, 705
trigger, I2S word select (WS) low, 706
trigger, I2S word select (WS) source, 696
trigger, IIC clock source, 709
trigger, IIC data source, 710
trigger, IIC pattern address, 711
trigger, IIC pattern data,
712
trigger, IIC pattern data 2, 713
trigger, IIC qualifier, 714
trigger, IIC signal baudrate, 721
trigger, IIC type, 715
trigger, LIN, 725
trigger, LIN pattern data, 727
trigger, LIN pattern data length, 729
trigger, LIN pattern format, 730
trigger, LIN sample point, 720
trigger, LIN signal definition, 1091
trigger, LIN source, 722
trigger, mode, 886
trigger, noise reject filter, 887
trigger, Nth edge burst source, 900
trigger, Nth edge in burst slope, 899
trigger, Nth edge of burst count, 897
trigger, Nth edge of Edge Then Edge
trigger, 893
trigger, SPI clock slope, 741
trigger, SPI clock source, 744
trigger, SPI clock timeout, 742
trigger, SPI frame source, 745
trigger, SPI framing, 743
trigger, SPI pattern MISO width, 749
trigger, SPI pattern MOSI width, 751
trigger, sweep, 888
trigger, threshold, 1094
trigger, TV line, 944
trigger, TV mode, 945, 1095
trigger, TV polarity, 946
trigger, TV source, 947
trigger, TV standard, 948
trigger, UART base, 769
trigger, UART baudrate, 758
trigger, UART bit order, 759
trigger, UART parity, 765
trigger, UART polarity, 766
trigger, UART Rx source, 767
trigger, UART Tx source, 768
trigger, UART width, 775
trigger, USB, 957
trigger, USB D- source, 954
trigger, USB D+ source, 955
trigger, USB speed, 956
truncation rules, 1140
TST (Self Test), 185
tstart, 1072
tstop, 1073
TTL threshold voltage for digital channels, 295,
1051
TTL trigger threshold voltage, 1094
turn function on or off, 1060
turn off channel, 198
turn off channel labels, 305
turn off digital pod, 198
turn off math function, 198
turn off time, 480, 556
turn on channel labels, 305
turn on channel number display, 1056
turn on time, 481, 556
turn on/turn off time analysis, 553, 554, 555,
556
turning channel display on and off, 266
turning off/on function calculation, 333
turning vectors on or off,
1055
TV mode, 945, 1095
TV trigger commands, 938, 943
TV trigger line number setting, 944
TV trigger mode, 947
TV trigger polarity, 946
TV trigger standard setting, 948
TV triggering, 878
tvmode, 1095
Tx data, UART, 985
Tx frame count (UART), 763
Tx source, 768
U
UART base, 769
UART baud rate, 758
UART bit order, 759
UART frame counters, reset, 761
UART parity, 765
UART polarity, 766
UART Rx source, 767
UART SEARch commands, 847
UART serial search, data, 848
UART serial search, data qualifier, 850
UART serial search, mode, 849
UART trigger burst, 770
UART trigger commands, 754
UART trigger data, 771
UART trigger idle, 772
UART trigger qualifier, 773
UART trigger type, 774
UART Tx data, 985
UART Tx source, 768
UART width, 775
UART/RS232 demo signal, 283
UART/RS-232 triggering, 630
units (vertical) for FFT, 336
units per division, 278, 279, 321, 871
units per division (vertical) for function, 278,
351
units, automask, 497
units, X cursor, 387, 388
units, Y cursor, 392, 393
unsigned data, 965
unsigned mode
, 987
upper threshold, 433
upper threshold voltage for
measurement, 1076
uppercase characters in commands, 1139
URQ (User Request) status bit, 166, 168
USB (Device) interface, 51
USB source, 954, 955
USB speed, 956
USB trigger, 957
USB trigger commands, 953
USB triggering, 878

Agilent Technologies InfiniiVision 3000 X-Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 3000 X-Series
Category	Test Equipment
Language	English