iPECS UCP - 6.13 DND Override

iPECS eMG80 & eMG800 & UCP
Administration and Programming Manual Issue 1.6
383
Table 4.4.5.20-1 SYSTEM TIMERS
ATTRIBUTE DESCRIPTION RANGE DEFAULT
VSF User Maximum
Record Timer
This timer sets the maximum duration allowed for the
User Greeting in the system’s VSF.
000~999
(seconds)
0
VSF Valid User
Message Timer
This timer sets the minimum duration allowed for a User
Greeting.
0~9
(seconds)
4
Door Open Timer
This timer sets the minimum time required to activate
the contact assigned as a door open contact.
00~99
(100 msec)
20
ICM Dial Tone Timer
If a user goes off-hook to receive Intercom dial tone and
takes no action for this timer, the user will receive error
tone.
001~255
(seconds)
10
Inter Digit Timer
This timer sets the maximum time allowed between
each user-dialed digit. At expiration, the user will
receive error-tone.
01~20
(seconds)
5
MSG Wait Reminder
Tone Timer
An iPECS IP or LDP Phone user will receive periodic
reminder tones of a message waiting at intervals of this
timer.
00~60
(minutes)
00
Paging Timeout Timer
Determines the maximum duration of a page after
which the caller and Page Zone are released.
000~255
(seconds)
15
Pause Timer
A Timed pause of this duration is used in speed dial
and during other automatically dialed digits sent to the
PSTN.
1~9
(seconds)
3
Soft auto RLS Timer
When a Soft Key is used on the 6000 or 7000 series
iPECS IP or LDP Phone, after expiration of this timer,
the display will return to the previous display.
1-30
(seconds)
10
VM Pause Timer
When the system sends a “Pause” to Voice Mail using
in-band signals, this timer defines the Pause duration.
(Not available in the USA.)
1-90
(ms)
30
SLT Hook Switch
Bounce Timer
This timer determines the duration the system
considers an actual state change in the hook-switch
and not a spurious contact bounce.
01~25
(100 msec.)
1
SLT Maximum Hook
Switch Flash Timer
This timer sets the maximum time an SLT user can
depress the hook-switch for a Flash signal.
01~25
(100 msec.)
10
SLT Minimum Hook
Flash Timer
This time sets the minimum time an SLT user must
depress the hook-switch for a Flash signal.
000~250
(10 msec.)
30
Station Auto Release
Timer
For an internal call, the system will return a station to
idle if the call remains unanswered for this duration.
000~300
(seconds)
60
Unsupervised
Conference Timer
This timer determines the duration of an “Unsupervised
Conference” before the station is recalled or the
conference is dropped. 00 means 10 minutes.
00~99
(minutes)
10
Prime Line Delay Timer
This timer sets the delay (no action duration) for
delayed (Warm) Prime Line operation.
01~20
(seconds)
5
Wink Signal Timer
This timer sets the duration of the “Seize Acknowledge
Signal” (Wink) sent to the PSTN on a DID line.
010~200
(10 msec.)
10
En-block Inter Digit
Timer
When an ISDN Line is assigned to send digits En-block,
CO Attribute section, the system will send digits if the
user dials “#” or this En-block inter-digit timer expires.
01~20
(seconds)
5
DTMF Duration Timer
This timer establishes the duration of DTMF tones sent
on an analog CO line.
04~99
(10 msec.)
10
Flex DID Timer
The system will receive DID digits for this timer.
After the timer expires, the system will use the last 2 to
01~99
(100 msec)
30