Cisco ONS 15454 DWDM - Table 5-4 TXP_MR_10 G and TXP_MR_10 E Transponder Card Line Settings

5-15
Cisco ONS 15454 DWDM Installation and Operations Guide, R6.0
September 2005
Chapter 5 Provision Transponder and Muxponder Cards
DLP-G217 Change Line Settings for TXP_MR_10G and TXP_MR_10E Cards
Table 5-4 TXP_MR_10G and TXP_MR_10E Transponder Card Line Settings
Parameter Description Options – ONS 15454 Options – ONS 15454 SDH
Port (Display only) Displays the port
number.
• 1-1 (OC192)
• 2 (Trunk)
• 1-1 (STM64)
• 2 (Trunk)
Port Name Provides the ability to assign the
specified port a name.
User-defined. Name can be up to
32 alphanumeric/special
characters. Blank by default.
See the “DLP-G104 Assign a
Name to a Port” task on page 7-10.
User-defined. Name can be up to
32 alphanumeric/special
characters. Blank by default.
See the “DLP-G104 Assign a
Name to a Port” task on page 7-10.
Admin State Sets the port service state. For more
information about administrative
states, see Appendix C, “DWDM
Administrative and Service
States.”
• IS
• IS,AINS
• OOS,DSBLD
• OOS,MT
• Unlocked
• Unlocked,automaticInService
• Locked,disabled
• Locked,maintenance
Service State (Display only) Identifies the
autonomously generated state that
gives the overall condition of the
port. Service states appear in the
format: Primary State-Primary
State Qualifier, Secondary State.
For more information about service
states, see Appendix C, “DWDM
Administrative and Service
States.”
• IS-NR
• OOS-AU,AINS
• OOS-MA,DSBLD
• OOS-MA,MT
• Unlocked-enabled
• Unlocked-disabled,
automaticInService
• Locked-enabled,disabled
• Locked-enabled,maintenance
SF BER (SONET [ANSI] or SDH [ETSI]
including 10G Ethernet WAN Phy
only) Sets the signal fail bit error
rate.
• 1E-3
• 1E-4
• 1E-5
• 1E-3
• 1E-4
• 1E-5
SD BER (SONET [ANSI] or SDH [ETSI]
including 10G Ethernet WAN Phy
only) Sets the signal degrade bit
error rate.
• 1E-5
• 1E-6
• 1E-7
• 1E-8
• 1E-9
• 1E-5
• 1E-6
• 1E-7
• 1E-8
• 1E-9
AINS Soak (SONET [ANSI] or SDH [ETSI]
including 10G Ethernet WAN Phy
only) Sets the automatic in-service
soak period. Double-click the time
and use the up and down arrows to
change settings.
• Duration of valid input signal,
in hh.mm format, after which
the card becomes in service
(IS) automatically
• 0 to 48 hours, 15-minute
increments
• Duration of valid input signal,
in hh.mm format, after which
the card becomes in service
(IS) automatically
• 0 to 48 hours, 15-minute
increments
Type (SONET [ANSI] or SDH [ETSI]
including 10G Ethernet WAN Phy
only) The optical transport type.
• SONET
• SDH
• SONET
• SDH