Cisco ONS 15454 DWDM User Manual

Contents
iv
Cisco ONS 15454 DWDM Installation and Operations Guide, R6.0
August 2005
Test Equipment (ETSI) 1-6
NTP- G1 Unpack and Inspect the Shelf Assembly 1-6
DLP- G1 Unpack and Verify the Shelf Assembly 1-6
DLP- G2 Inspect the Shelf Assembly 1-7
NTP- G2 Install the Shelf Assembly 1-8
DLP- G3 Reverse the Mounting Bracket to Fit a 19-inch (482.6-mm) Rack (ANSI Only) 1-10
DLP- G4 Install the External Brackets and Air Filter (ANSI Only) 1-11
DLP- G5 Mount the Shelf Assembly in a Rack (One Person) 1-13
DLP- G6 Mount the Shelf Assembly in a Rack (Two People) 1-15
DLP- G7 Mount Multiple Shelf Assemblies in a Rack 1-16
DLP- G8 Install the Air Ramp 1-19
NTP- G3 Open and Remove the Front Door 1-20
DLP- G9 Open the Front Cabinet Compartment (Door) 1-20
DLP- G10 Remove the Front Door 1-21
NTP- G4 Open and Remove the FMEC Cover (ETSI Only) 1-23
DLP- G11 Open the FMEC Cover 1-24
DLP- G12 Remove the FMEC Cover 1-25
NTP- G5 Remove the Backplane Covers (ANSI Only) 1-26
DLP- G13 Remove the Lower Backplane Cover 1-26
DLP- G14 Remove the Backplane Sheet Metal Cover 1-27
NTP- G6 Install the MIC-A/P and MIC-T/C/P FMECs (ETSI Only) 1-28
NTP- G7 Install the Power and Ground 1-30
DLP- G15 Connect the Office Ground to the ONS 15454 ETSI 1-32
DLP- G16 Connect the Office Ground to the ONS 15454 ANSI 1-34
DLP- G17 Connect Office Power to the ONS 15454 ETSI 1-35
DLP- G18 Connect Office Power to the ONS 15454 ANSI 1-37
DLP- G19 Turn On and Verify Office Power 1-39
NTP- G8 Install the Fan-Tray Assembly 1-40
NTP- G9 Install the Alarm Expansion Panel (ANSI Only) 1-44
NTP- G10 Attach Wires to Alarm, Timing, LAN, and Craft Pin Connections 1-47
DLP- G20 Install Alarm Wires on the MIC-A/P (ETSI Only) 1-48
DLP- G21 Install Timing Wires on the MIC-C/T/P (ETSI Only) 1-51
DLP- G22 Install LAN Wires on the MIC-C/T/P (ETSI Only) 1-52
DLP- G23 Install Alarm Wires on the Backplane (ANSI Only) 1-53
DLP- G24 Install Timing Wires on the Backplane (ANSI Only) 1-55
DLP- G25 Install LAN Wires on the Backplane (ANSI Only) 1-56
DLP- G26 Install the TL1 Craft Interface (ANSI Only) 1-57
NTP- G11 Install an External Wire-Wrap Panel on the AEP (ANSI Only) 1-58

Cisco ONS 15454 DWDM Specifications

General

Chassis Type	DWDM
Form Factor	Rack-mountable
Slots	17
Storage Temperature	-40 to 158°F (-40 to 70°C)
Relative Humidity	5% to 95% non-condensing
Power Supply	AC or DC
Cooling	Internal fans
Operating Temperature	23 to 104°F (-5 to 40°C)
Altitude	0 to 6500 ft (0 to 1981 m)
Safety Compliance	EN 60950-1
EMI Compliance	FCC Part 15