14-3
Cisco ONS 15454 DWDM Installation and Operations Guide, R6.0
August 2005
Chapter 14 Power Down a Node
NTP-G119 Power Down the Node
c. Click the Provisioning > Optical Chn > Parameters tabs.
d. In the Admin State column for each line, make sure that the default state IS, AINS (ANSI) or
Unlocked,automaticInservice (ETSI) is selected.
Step 9 For each installed DWDM band-bearing card (AD-1B-xx.x and AD-4B-xx.x, where xx.x refers to the
specific wavelengths), make sure all lines and bands are not in the IS-NR (ANSI) or Unlocked-Enabled
(ETSI) service state:
a. In the card view, click the Provisioning > Optical Line > Parameters tabs.
b. In the Admin State column for each line, make sure that the default state IS, AINS (ANSI) or
Unlocked,automaticInservice (ETSI) is selected.
c. Click the Provisioning > Optical Band > Parameters tabs.
d. In the Admin State column for each line, make sure that the default state IS, AINS (ANSI) or
Unlocked,automaticInservice (ETSI) is selected.
Step 10 For each installed DWDM transponder (TXP), muxponder (MXP), multiplexer, demultiplexer or
amplifier card (32MUX-O, 32DMX-0, 32DMX, 32WSS, 4MD-xx.x, OPT-BST, OPT-PRE,
TXP_MR_10G, TXP_MR_10E, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_2.5G_10G, MXP_2.5G_10E,
MXP_MR_2.5G, MXPP_MR_2.5G), make sure all lines are not in the IS-NR (ANSI) or
Unlocked-enabled (ETSI) service state:
a. In card view, click the appropriate tab depending on the card:
• For MXP_2.5G_10G, TXP_MR_10G, TXP_MR_10E cards, click the Provisioning > Line >
SONET tabs if the card was provisioned for a SONET payload, or the Provisioning > Line >
SDH tabs if the card was provisioned for an SDH payload.
• For TXP_MR_2.5G, TXPP_MR_2.5G, and MXPP_MR_2.5G cards, click the Provisioning >
Line > OC48 tabs.
• For MXP_2.5G_10E cards, click the Provisioning > Line > Trunk tabs.
• For MXP_MR_2.5G cards, click the Provisioning > Line > Client tabs.
• For 32MUX-O, 32DMX-0, 32DMX, 32WSS, OPT-BST, OPT-PRE cards, click the
Provisioning > Optical Line > Parameters tabs.
• For 32DMX and 32DMX-O cards, click the Provisioning > Optical Chn > Parameters tabs.
• For 4MD-xx.x cards, click the Provisioning > Optical Band > Parameters tabs.
• For OPT-BST and OPT-PRE cards, click the Provisioning > Optical Ampli Line > Parameters
tabs.
b. In the Admin State column for each line, make sure that the default state IS, AINS (ANSI) or
Unlocked,automaticInservice (ETSI) is selected.
c. Repeat Steps a and b for each installed DWDM card.
Note Ports are put in service when circuits are provisioned, and put out of service when circuits are deleted.
When circuits are deleted the Admin State displays as IS, AINS (ANSI) or Unlocked,automaticInservice
(ETSI) and the Service State displays OOS-AU,AINS (ANSI) or Unlocked-disabled,automaticInService
(ETSI).
Step 11 Remove all fiber connections to the cards.
Step 12 In node view, right-click an installed card and click Delete.
Step 13 Click Yes .
To Next Page
Loading...
