Lexmark C950 - Page 999

Index I-7
5058-030
Go Back
Previous
Next
HCF media size L 4-371
HCF media size R 4-371
HCF media tray set 4-372
HCF top door interlock) 4-383
HCF unit docking interlock 4-382
image calibration 4-147
lower media exit 4-322
media eject clamp HP 4-323
media eject shaft HP 4-324
media on belt 4-149
printer left duplex door interlock 4-152
printer right front door interlock 4-156
punch cam HP 4-326
punch carriage shift HP 4-325
punch hole select 4-326
punch unit motor encoder 4-327
punch unit side reg 1 4-328
punch unit side reg 2 4-328
punch waste box set 4-329
rear tamper HP 4-321
stacker bin level encoder 4-330
stacker bin level F 4-331
stacker bin level R 4-331
stacker bin no media 4-332
stacker bin upper limit 4-332
stapelr carriage HP 4-334
tray 1 media level 4-197
tray 1 media out 4-197
tray 1 pre feed 4-157
tray 2 media level 4-197
tray 2 media out 4-197
tray 3 media level 4-197
tray 3 media out 4-197
tray 4 media level 4-197
tray 4 media out 4-197
tray 5 feed out 4-373
tray 5 media level 4-384
tray 5 media out 4-385
tray module feed out 4-200
tray module feedout 4-200
tray module left door interlock 4-201
TTM media size) 4-203
TTM tray 3 feedout 4-203
TTM tray 4 feedout 4-204
upper media bin full 4-335
upper media exit 4-336
sensor tests 3-23
service checks 2-34
1xx service checks 2-34
2xx service checks 2-81
3xx service checks 2-131
4xx service checks 2-177
8xx service checks 2-208
900.xx System software 2-211
9xx service checks 2-214
service error, 900.xx System software error 2-211
service menus, accessing 3-4
SFP operator panel 4-123
SFP operator panel PCBA 4-124
SFP operator panel top cover 4-8
SFP RIP PCBA 4-144
SFP touch screen 4-167
specifications, media
input and output sources
1-6
media input size specifications 1-6
media input type specifications 1-7
supported finishing features 1-9
specifications, printer
clearances
1-4
connectivity (network support) 1-3
data streams 1-4
dimensions 1-4
electronics 1-2
environment specifications 1-5
operating modes 1-3
SFP 1-2
stacker media bin 4-340
staple test 3-18
stapler unit assembly 4-340
stapler unit frame 4-342
sub LVPS PCBA 4-158
sub paddle 4-349
suction fan 4-161
suction filter 4-163
T
theory of operations
1TM
3-116
3TM 3-110
finisher 3-71
HCF 3-122
print engine 3-52
TTM 3-103
toner smart chip PCB 4-166
tools required 1-14
transfer belt assembly 4-168
transfer belt cleaner 4-172
transfer belt lever 4-174
transfer roll HVPS PCBA 4-175
tray module bottom cover 4-205
tray module controller PCBA 4-206
tray module left cover 4-206
tray module lower transport motor 4-207
tray module rear cover 4-211
tray module right cover 4-211
tray module top cover 4-212
tray module transport roller 4-213
tray module tray 2 media turn guide 4-214
tray module upper transport motor 4-214
TTM left door 4-215
TTM lower transport motor 4-216
TTM theory
main components
3-107
media transport 3-104
media tray assembly 3-104
TTM media feed units 3-106
TTM tray 3 feeder 4-217
TTM tray 3 media tray 4-220
TTM tray 3 media turn guide 4-221