2 Parameters
2.2 List of parameters
SINAMICS DCM
234 List Manual (LH8), 02/2015, 6RX1800-0ED76
Description: Displays the inverted status of the raw data of the digital inputs of the Terminal Module 15 (TM15).
Notice: The raw data of the digital inputs is directly displayed (e.g. without any debounce).
Note: Should only used for internal Siemens purposes (alternative r4022, r4023).
Description: Sets the simulation mode for the digital inputs of Terminal Module 15 (TM15).
r4094.0...23 BO: TM15 digital inputs status inverted raw data internal / TM15 DI st raw dat
TM15DI_DO Can be changed: - Calculated: - Access level: 4
Data type: Unsigned32 Dyn. index: - Func. diagram: -
P-Group: Commands Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - -
Bit field: Bit Signal name 1 signal 0 signal FP
00 DI/DO 0 (X520.2) High Low -
01 DI/DO 1 (X520.3) High Low -
02 DI/DO 2 (X520.4) High Low -
03 DI/DO 3 (X520.5) High Low -
04 DI/DO 4 (X520.6) High Low -
05 DI/DO 5 (X520.7) High Low -
06 DI/DO 6 (X520.8) High Low -
07 DI/DO 7 (X520.9) High Low -
08 DI/DO 8 (X521.2) High Low -
09 DI/DO 9 (X521.3) High Low -
10 DI/DO 10 (X521.4) High Low -
11 DI/DO 11 (X521.5) High Low -
12 DI/DO 12 (X521.6) High Low -
13 DI/DO 13 (X521.7) High Low -
14 DI/DO 14 (X521.8) High Low -
15 DI/DO 15 (X521.9) High Low -
16 DI/DO 16 (X522.2) High Low -
17 DI/DO 17 (X522.3) High Low -
18 DI/DO 18 (X522.4) High Low -
19 DI/DO 19 (X522.5) High Low -
20 DI/DO 20 (X522.6) High Low -
21 DI/DO 21 (X522.7) High Low -
22 DI/DO 22 (X522.8) High Low -
23 DI/DO 23 (X522.9) High Low -
p4095 TM15DI/DO digital inputs simulation mode / TM15D DI sim_mode
TM15DI_DO Can be changed: U, T Calculated: - Access level: 2
Data type: Unsigned32 Dyn. index: - Func. diagram: 9400, 9401,
9402
P-Group: Terminals Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0000 0000 0000 0000 0000
0000 0000 0000 bin
Bit field: Bit Signal name 1 signal 0 signal FP
00 DI/DO 0 (X520.2) Simulation Terminal eval -
01 DI/DO 1 (X520.3) Simulation Terminal eval -
02 DI/DO 2 (X520.4) Simulation Terminal eval -
03 DI/DO 3 (X520.5) Simulation Terminal eval -
04 DI/DO 4 (X520.6) Simulation Terminal eval -
05 DI/DO 5 (X520.7) Simulation Terminal eval -
06 DI/DO 6 (X520.8) Simulation Terminal eval -
07 DI/DO 7 (X520.9) Simulation Terminal eval -
08 DI/DO 8 (X521.2) Simulation Terminal eval -
09 DI/DO 9 (X521.3) Simulation Terminal eval -
10 DI/DO 10 (X521.4) Simulation Terminal eval -
11 DI/DO 11 (X521.5) Simulation Terminal eval -
To Next Page
Loading...
