EasyManuals Logo

Siemens SINAMICS DCM List Manual

Siemens SINAMICS DCM
1204 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #433 background imageLoading...
Page #433 background image
SINAMICS DCM
List Manual (LH8), 02/2015, 6RX1800-0ED76
433
2 Parameters
2.2 List of parameters
Value: 0: Deactivated
1: Activated
Dependency: Refer to: p50284
Note: If value = 0:
The integral component of the EMF controller is kept constantly at zero (i.e. the EMF controller functions solely as a
proportional controller).
Description: Sets the P gain of the EMF controller.
Dependency: Refer to: p50276
Note: The parameter is set automatically during the optimization run for field weakening (p50051 = 27).
Description: Sets the integral time of the EMF controller.
Dependency: Refer to: p50275
Note: The parameter is set automatically during the optimization run for field weakening (p50051 = 27).
Description: Sets the value for the EMF controller's droop feedback.
Note: If value = 0:
Droop feedback is de-activated.
Description: Sets the smoothing time constant for the setpoint for EMF controller pre-control.
Dependency: Refer to: p50283
Note: This smoothing enables the EMF controller pre-control to be decoupled from the EMF controller.
p50275[0...n] EMF controller P gain / EMF ctr Kp
DC_CTRL Can be changed: U, T Calculated: - Access level: 2
Data type: FloatingPoint32 Dyn. index: DDS, p0180 Func. diagram: 6900
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0.01 100.00 0.60
p50276[0...n] EMF controller integral time / EMF ctr Tn
DC_CTRL Can be changed: U, T Calculated: - Access level: 2
Data type: FloatingPoint32 Dyn. index: DDS, p0180 Func. diagram: 6900
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0.010 [s] 10.000 [s] 0.200 [s]
p50277[0...n] EMF controller droop / EMF ctr droop
DC_CTRL Can be changed: U, T Calculated: - Access level: 2
Data type: FloatingPoint32 Dyn. index: DDS, p0180 Func. diagram: 6900
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: PERCENT Expert list: 1
Min Max Factory setting
0.0 [%] 10.0 [%] 0.0 [%]
p50280[0...n] EMF controller pre-control setpoint smoothing time constant / EMF prec set T
DC_CTRL Can be changed: U, T Calculated: - Access level: 2
Data type: FloatingPoint32 Dyn. index: DDS, p0180 Func. diagram: 6900
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0 [ms] 10000 [ms] 0 [ms]

Table of Contents

Other manuals for Siemens SINAMICS DCM

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINAMICS DCM and is the answer not in the manual?

Siemens SINAMICS DCM Specifications

General IconGeneral
BrandSiemens
ModelSINAMICS DCM
CategoryMedia Converter
LanguageEnglish

Related product manuals