Siemens SINAMICS DCM - Cbe2 X Default Gateway of Station Active; Cbe2 X Def GW Act; Cbe2 X DHCP Mode Active; Cbe2 X DHCP Act; Cbe2 X MAC Address of Station; Cbe2 X MAC Addr; Cbe2 X Subnet Mask of Station Active; Cbe2 X Sub Mask Act

SINAMICS DCM
List Manual (LH8), 02/2015, 6RX1800-0ED76
347
2 Parameters
2.2 List of parameters
Description: Displays the active standard gateway for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Description: Displays the active subnet mask for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Description: Displays the active DHCP mode for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Notice: When the DHCP mode is active (parameter value greater than 0), PROFINET communication via this interface is no
longer possible! However, the interface can be used by the STARTER/SCOUT commissioning tool.
Note: If value = 0:
DHCP deactivated.
If value = 2:
DHCP activated. The MAC address of this interface is used for client identification.
If value = 3:
DHCP activated. The station name of this interface is used for client identification.
Description: Displays the MAC address for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Description: Displays the DAP ID for PROFINET via the Communication Board Ethernet 20/25 (CBE20/CBE25).
r8952[0...3] CBE2x Default Gateway of Station active / CBE2x def GW act
CU_DC (PROFINET
CBE20), CU_DC_R
(PROFINET CBE20),
CU_DC_R_S
(PROFINET CBE20),
CU_DC_S
(PROFINET CBE20)
Can be changed: - Calculated: - Access level: 3
Data type: Unsigned8 Dyn. index: - Func. diagram: -
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0 255 -
r8953[0...3] CBE2x Subnet Mask of Station active / CBE2x Sub Mask act
CU_DC (PROFINET
CBE20), CU_DC_R
(PROFINET CBE20),
CU_DC_R_S
(PROFINET CBE20),
CU_DC_S
(PROFINET CBE20)
Can be changed: - Calculated: - Access level: 3
Data type: Unsigned8 Dyn. index: - Func. diagram: -
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0 255 -
r8954 CBE2x DHCP Mode active / CBE2x DHCP act
CU_DC (PROFINET
CBE20), CU_DC_R
(PROFINET CBE20),
CU_DC_R_S
(PROFINET CBE20),
CU_DC_S
(PROFINET CBE20)
Can be changed: - Calculated: - Access level: 3
Data type: Unsigned8 Dyn. index: - Func. diagram: -
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0 255 -
r8955[0...5] CBE2x MAC Address of Station / CBE2x MAC Addr
CU_DC (PROFINET
CBE20), CU_DC_R
(PROFINET CBE20),
CU_DC_R_S
(PROFINET CBE20),
CU_DC_S
(PROFINET CBE20)
Can be changed: - Calculated: - Access level: 3
Data type: Unsigned8 Dyn. index: - Func. diagram: -
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0000 hex 00FF hex -
r8959 CBE2x DAP ID / CBE2x DAP ID
CU_DC (PROFINET
CBE20), CU_DC_R
(PROFINET CBE20),
CU_DC_R_S
(PROFINET CBE20),
CU_DC_S
(PROFINET CBE20)
Can be changed: - Calculated: - Access level: 3
Data type: Unsigned32 Dyn. index: - Func. diagram: -
P-Group: - Unit group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
0000 hex FFFF FFFF hex -