SINAMICS DCM
List Manual (LH8), 02/2015, 6RX1800-0ED76
647
2 Parameters
2.3 Parameters for data sets
p2298[0...n] CI: Technology controller minimum limit signal source / Tec_ctrl min_l s_s
p2299[0...n] CI: Technology controller limit offset / Tech_ctrl lim offs
p3111[0...n] BI: External fault 3 enable / Ext fault 3 enab
p3112[0...n] BI: External fault 3 enable negated / Ext flt 3 enab neg
p50165[0...n] BI: Signal source for change in torque direction enable / Torq dir en sig s
p50173[0...n] BI: Signal source for closed-loop current/torque control ctr type / Ctr I/tq ctr sig s
p50175[0...n] CI: Signal source for closed-loop armature current control P gain / Ia ctr Kp sig s
p50176[0...n] CI: Signal source for closed-loop armature current ctr integr time / Ia ctr Tn sig s
p50177[0...n] BI: Signal source for the "No immediate pulse inhibit" command / No pulse inh sig s
p50178[0...n] BI: Sig source for the "Fire all thyristors simultaneously" command / All thy fire sig s
p50265[0...n] BI: Signal source for field current monitoring / I_field mon sig s
p50266[0...n] CI: Field current controller Tn factor signal source / If_ctrTnFact sig s
p50267[0...n] CI: Field current controller Kp factor signal source / If_ctrKpFact sig s
p50289[0...n] BI: EMF setpoint reduction activation signal source / EMF set act sig s
p50322[0...n] CI: Setpoint processing signal source for main setpoint factor / M set factor sig s
p50323[0...n] CI: Setpoint processing signal source for additional setpoint factor / Add set fac sig s
p50433[0...n] CI: Signal source for default setpoint / Def set sig s
p50438[0...n] CI: Jog signal source for default setpoint / Jog def set sig s
p50443[0...n] CI: Creep signal source for default setpoint / Cr def set sig s
p50444[0...n] BI: Creep signal source for shutdown / Cr shutdn sig s
p50461[0...n] CI: Motorized potentiometer signal source for automatic setpoint / MotP aut s sig s
p50466[0...n] CI: Motor potentiometer setting value signal source / MotP s val sig s
p50470[0...n] BI: Motorized potentiometer signal source for CW/CCW / MotP CW/CCW sig s
p50471[0...n] BI: Motorized potentiometer signal source for manual/automatic / MotP man/aut sig s
p50472[0...n] BI: Motorized potentiometer accept setting value / MotP acc set val
p50484[0...n] CI: Oscillation signal source for default setpoint / Oscill def set
p50485[0...n] BI: Oscillation selection of signal source / Oscill sel sig s
p50500[0...n] CI: Torque limiting signal source for t_set in slave mode / T_set s mode sig s
p50501[0...n] CI: Torque limiting signal source for torque additional setpoint / T_lim add s sig s
p50553[0...n] CI: Speed controller adaptation Kp signal source / Adapt Kp sig s
p50554[0...n] CI: Speed controller adaptation Tn signal source / Adapt Tn sig s
p50555[0...n] CI: Speed controller adaptation droop signal source / Adapt droop sig s
p50580[0...n] BI: Field reversal direction of rotation signal source / Field rev sig s
p50581[0...n] BI: Field reversal braking signal source / Field rev br sig s
p50583[0...n] CI: Field reversal speed actual value signal source / FldRev n_act sig s
p50594[0...n] CI: Messages polarity speed setpoint signal source / MsgPol n_set S_src
p50598[0...n] CI: Messages polarity speed actual value signal source / MsgPol n_act S_src
p50607[0...n] CI: Torque limiting signal source for master drive t_set / Mst tq set sig s
p50609[0...n] CI: Signal source for speed controller actual value / n_ctr act sig s
p50625[0...n] CI: Signal source for speed controller setpoint / n_ctr set sig s
p50626[0...n] CI: Signal source for speed controller actual value smoothing / Act v smoo sig s
p50635[0...n] CI: Setpoint processing signal source for RFG setpoint / RFG set sig s
p50637[0...n] BI: RFG parameter set 2 selection signal source / RFG par s 2 sig s
p50638[0...n] BI: RFG parameter set 3 selection signal source / RFG par s 3 sig s
p50640[0...n] BI: RFG signal source for accepting setting value / RFG accept set v
p50641[0...n] BI: Bypass ramp-function generator signal source / Bypass RFG sig s
p50644[0...n] CI: Setpoint processing signal source for main setpoint / M set sig s
p50645[0...n] CI: Setpoint processing signal source for additional setpoint / A set sig s
p50646[0...n] BI: RFG signal source for ramp-up integrator enable / R-up int ena sig s
p50647[0...n] BI: RFG tracking activation signal source / RFG trck act sig s
p50671[0...n] BI: Setpoint processing sig source to enable neg dir of rotation / Ena n dir r sig s
p50672[0...n] BI: Setpoint processing signal source to enable pos dir of rotation / Ena p dir r sig s
p50673[0...n] BI: Motorized potentiometer signal source to increase setpoint / MotP incr sig s
p50674[0...n] BI: Motorized potentiometer signal source to lower setpoint / MotP lower sig s
p50680[0...n] BI: Fixed setpoint signal source for connector selection 0 / Fix set con0 sig s
To Next Page
Loading...
