SINAMICS DCM
List Manual (LH8), 02/2015, 6RX1800-0ED76
649
2 Parameters
2.3 Parameters for data sets
p50112[0...n] Field circuit resistance / R_field circuit
p50113[0...n] Motor I2t monitoring continuous current factor / Mot I2t I_cont
p50114[0...n] Motor thermal time constant / Mot T therm
p50115[0...n] Speed controller EMF at maximum speed / EMF at n_max
p50116[0...n] Field circuit inductance / L_field circuit
p50117[0...n] Field characteristic status / Field char stat
p50118[0...n] EMF rated value / EMF rated
p50119[0...n] Rated speed / n_rated
p50120[0...n] Field current for motor flux 0 % / I_field flux 0%
p50121[0...n] Field current for motor flux 5 % / I_field flux 5%
p50122[0...n] Field current for motor flux 10 % / I_field flux 10%
p50123[0...n] Field current for motor flux 15 % / I_field flux 15%
p50124[0...n] Field current for motor flux 20 % / I_field flux 20%
p50125[0...n] Field current for motor flux 25 % / I_field flux 25%
p50126[0...n] Field current for motor flux 30 % / I_field flux 30%
p50127[0...n] Field current for motor flux 35 % / I_field flux 35%
p50128[0...n] Field current for motor flux 40 % / I_field flux 40%
p50129[0...n] Field current for motor flux 45 % / I_field flux 45%
p50130[0...n] Field current for motor flux 50 % / I_field flux 50%
p50131[0...n] Field current for motor flux 55 % / I_field flux 55%
p50132[0...n] Field current for motor flux 60 % / I_field flux 60%
p50133[0...n] Field current for motor flux 65 % / I_field flux 65%
p50134[0...n] Field current for motor flux 70 % / I_field flux 70%
p50135[0...n] Field current for motor flux 75 % / I_field flux 75%
p50136[0...n] Field current for motor flux 80 % / I_field flux 80%
p50137[0...n] Field current for motor flux 85 % / I_field flux 85%
p50138[0...n] Field current for motor flux 90 % / I_field flux 90%
p50139[0...n] Field current for motor flux 95% / I_field flux 95%
p50148[0...n] Armature converter Alpha W limit (single-phase operation) / A Alpha W lim 1-ph
p50149[0...n] Armature converter correction angle Alpha W limit / Arm corr Alpha W
p50150[0...n] Armature converter Alpha G limit / Arm Alpha G lim
p50151[0...n] Armature converter Alpha W limit / Arm Alpha W lim
p50152[0...n] Armature average number of line periods / Arm line per no.
p50153[0...n] Control word for armature pre-control / A prec STW
p50154[0...n] Closed-loop armature current control integral comp activation / Ia ctr I comp act
p50155[0...n] Closed-loop armature current control P gain / Ia ctr Kp
p50156[0...n] Closed-loop armature current control integral time / Ia ctr Tn
p50157[0...n] Current limitation setpoint integrator selection / I_set integ sel
p50158[0...n] Current limitation setpoint integrator ramp-up time / Set integ t_r-up
p50159[0...n] Auto-reversing stage changeover threshold / Auto-rev thresh
p50160[0...n] Auto-reversing stage additional torque-free interval / Auto-rev interval
p50161[0...n] Auto-reversing stage Alpha W pulses second pulse inhibited / Auto-rev Alpha W1
p50162[0...n] EMF selection / EMF sel
p50163[0...n] EMF smoothing selection / EMF smoothing sel
p50164[0...n] Closed-loop armature current ctr proportional comp activation / Ia ctr Kp act
p50169[0...n] Torque limiting selection torque limiting/current limitation / T lim sel T/I_lim
p50170[0...n] Selection of control type for closed-loop current/torque control / Ctrl type I/tq sel
p50171[0...n] Current limitation armature current limit torque dir I factor / Ia lim t d I fact
p50172[0...n] Current limitation armature current limit torque dir II factor / Ia lim t d II fact
p50179[0...n] Auto-reversing stage Alpha W pluses second pulse enabled / Auto-rev Alpha W2
p50180[0...n] Torque limiting torque limit 1 positive / T lim 1 pos
p50181[0...n] Torque limiting torque limit 1 negative / T lim 1 neg
p50182[0...n] Torque limiting torque limit 2 positive / T lim 2 pos
p50183[0...n] Torque limiting torque limit 2 negative / T lim 2 neg
p50184[0...n] Torque limiting changeover speed / T lim n_chng
To Next Page
Loading...
