EasyManua.ls Logo

Siemens SINAMICS G150 - Page 1016

Siemens SINAMICS G150
1842 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
2 Parameters
2.3 Parameters for data sets
SINAMICS G130/G150
1016 List Manual (LH2), 04/2014, A5E03263479A
p0625[0...n] Motor ambient temperature during commissioning / Mot T_ambient
p0626[0...n] Motor overtemperature, stator core / Mot T_over core
p0627[0...n] Motor overtemperature, stator winding / Mot T_over stator
p0628[0...n] Motor overtemperature rotor winding / Mot T_over rotor
p0629[0...n] Stator resistance reference / R_stator ref
r0630[0...n] Mot_temp_mod ambient temperature / Mod T_ambient
r0631[0...n] Mot_temp_mod stator iron temperature / Mod T_stator
r0632[0...n] Mot_temp_mod stator winding temperature / Mod T_winding
r0633[0...n] Mot_temp_mod rotor temperature / Mod rotor temp
p0634[0...n] Q flux flux constant unsaturated / PSIQ KPSI UNSAT
p0635[0...n] Q flux quadrature axis current constant unsaturated / PSIQ KIQ UNSAT
p0636[0...n] Q flux direct axis current constant unsaturated / PSIQ KID UNSAT
p0637[0...n] Q flux flux gradient saturated / PSIQ Grad SAT
p0643[0...n] Overvoltage protection for synchronous motors / Overvolt_protect
p0650[0...n] Actual motor operating hours / Mot t_oper act
p0651[0...n] Motor operating hours maintenance interval / Mot t_op maint
p0652[0...n] Motor stator resistance scaling / Mot R_stator scal
p0653[0...n] Motor stator leakage inductance scaling / Mot L_S_leak scal
p0655[0...n] Motor magnetizing inductance d axis saturated scaling / Mot L_m d sat scal
p0656[0...n] Motor magnetizing inductance q axis saturated scaling / Mot L_m q sat scal
p0657[0...n] Motor damping inductance d axis scaling / Mot L_damp d scal
p0658[0...n] Motor damping inductance q axis scaling / Mot L_damp q scal
p0659[0...n] Motor damping resistance d axis scaling / Mot R_damp d scal
p0660[0...n] Motor damping resistance q axis scaling / Mot R_damp q scal
p0826[0...n] Motor changeover motor number / Mot_chng mot No.
p0827[0...n] Motor changeover status word bit number / Mot_chg ZSW bitNo.
p1231[0...n] Armature short-circuit / DC braking configuration / ASC/DCBRK config
p1232[0...n] DC braking braking current / DCBRK I_brake
p1233[0...n] DC braking time / DCBRK time
p1234[0...n] Speed at the start of DC braking / DCBRK n_start
p1236[0...n] Ext. armature short-cct. contactor feedback signal monit. time / ASC ext t_monit
p1237[0...n] External armature short-circuit delay time when opening / ASC ext t_wait
p1909[0...n] Motor data identification control word / MotID STW
p1980[0...n] PolID technique / PolID technique
p1982[0...n] PolID selection / PolID selection
p1991[0...n] Motor changeover angular commutation correction / Ang_com corr
p1999[0...n] Ang. commutation offset calibr. and PollD scaling / Com_ang_offs scal
p4610[0...n] Motor temperature sensor 1 sensor type MDS / Temp sens1 typ MDS
p4611[0...n] Motor temperature sensor 2 sensor type MDS / Temp sens2 typ MDS
p4612[0...n] Motor temperature sensor 3 sensor type MDS / Temp sens3 typ MDS
p4613[0...n] Motor temperature sensor 4 sensor type MDS / Temp sens4 typ MDS
r5398[0...n] Mot_temp_mod 3 alarm threshold image p5390 / A thr image p5390
r5399[0...n] Mot_temp_mod 3 fault threshold image p5391 / F thr image p5391

Table of Contents

Other manuals for Siemens SINAMICS G150

Related product manuals