Siemens SINAMICS G150 - BI: Input Signal Bit-Serially 1; Input_Sig Bit 1; CI: Input Signal Word-Serially 0; Input_Sig Word 0; CI: Input Signal Word-Serially 1; Input_Sig Word 1

SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
747
2 Parameters
2.2 List of parameters
Dependency: Refer to: r8510
Description: Sets the signal source for bit-serial input signals.
These signals are available in binector output r8511.0 ... 21 for further interconnection.
Index: [0] = To BO: r8511.0
[1] = To BO: r8511.1
[2] = To BO: r8511.2
[3] = To BO: r8511.3
[4] = To BO: r8511.4
[5] = To BO: r8511.5
[6] = To BO: r8511.6
[7] = To BO: r8511.7
[8] = To BO: r8511.8
[9] = To BO: r8511.9
[10] = To BO: r8511.10
[11] = To BO: r8511.11
[12] = To BO: r8511.12
[13] = To BO: r8511.13
[14] = To BO: r8511.14
[15] = To BO: r8511.15
[16] = To BO: r8511.16
[17] = To BO: r8511.17
[18] = To BO: r8511.18
[19] = To BO: r8511.19
[20] = To BO: r8511.20
[21] = To BO: r8511.21
Dependency: Refer to: r8511
Description: Sets the signal source for wordwise input signals.
This signal value is available in connector output r8512 for further interconnection.
Dependency: Refer to: r8512
Description: Sets the signal source for wordwise input signals.
This signal value is available in connector output r8513 for further interconnection.
Dependency: Refer to: r8513
p8501[0...21] BI: Input signal bit-serially 1 / Input_sig bit 1
CU_G130_DP,
CU_G130_PN,
CU_G150_DP,
CU_G150_PN
Can be changed: U, T Calculated: - Access level: 2
Data type: Unsigned32 / Binary Dyn. index: - Func. diagram: 2195
P-Group: - Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0
p8502 CI: Input signal word-serially 0 / Input_sig word 0
CU_G130_DP,
CU_G130_PN,
CU_G150_DP,
CU_G150_PN
Can be changed: U, T Calculated: - Access level: 2
Data type: Unsigned32 / Integer32 Dyn. index: - Func. diagram: 2195
P-Group: - Units group: - Unit selection: -
Not for motor type: - Scaling: PERCENT Expert list: 1
Min Max Factory setting
- - 0
p8503 CI: Input signal word-serially 1 / Input_sig word 1
CU_G130_DP,
CU_G130_PN,
CU_G150_DP,
CU_G150_PN
Can be changed: U, T Calculated: - Access level: 2
Data type: Unsigned32 / Integer32 Dyn. index: - Func. diagram: 2195
P-Group: - Units group: - Unit selection: -
Not for motor type: - Scaling: PERCENT Expert list: 1
Min Max Factory setting
- - 0