Siemens SINAMICS G150 - BI: TB30 Signal Source for Terminal DO 3; TB30 S S DO 3; BI: TM31 Signal Source for Terminal DI;DO 8; TM31 S_Src DI;DO8; BI: TM31 Signal Source for Terminal DI;DO 9; TM31 S_Src DI;DO9; BI: TM31 Signal Source for Terminal DI;DO 10; TM31 S_Src DI;DO10

2 Parameters
2.2 List of parameters
SINAMICS G130/G150
604 List Manual (LH2), 04/2014, A5E03263479A
Description: Sets the signal source for terminal DO 3 (X481.8) of the Terminal Board 30 (TB30).
Note: DO: Digital Output
Description: Sets the signal source for terminal DI/DO 8 (X541.2) of Terminal Module 31 (TM31).
Note: Prerequisite: The DI/DO must be set as an output (p4028.8 = 1).
DI/DO: Bidirectional Digital Input/Output
Description: Sets the signal source for terminal DI/DO 9 (X541.3) of Terminal Module 31 (TM31).
Note: Prerequisite: The DI/DO must be set as an output (p4028.9 = 1).
DI/DO: Bidirectional Digital Input/Output
Description: Sets the signal source for terminal DI/DO 10 (X541.4) of Terminal Module 31 (TM31).
Note: Prerequisite: The DI/DO must be set as an output (p4028.10 = 1).
DI/DO: Bidirectional Digital Input/Output
Description: Sets the signal source for terminal DI/DO 11 (X541.5) of Terminal Module 31 (TM31).
p4033 BI: TB30 signal source for terminal DO 3 / TB30ssDO3
TB30 Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dyn. index: - Func. diagram: 9099, 9102
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0
p4038 BI: TM31 signal source for terminal DI/DO 8 / TM31 S_src DI/DO8
TM31 Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dyn. index: - Func. diagram: 9549, 9560
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0
p4039 BI: TM31 signal source for terminal DI/DO 9 / TM31 S_src DI/DO9
TM31 Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dyn. index: - Func. diagram: 9560
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0
p4040 BI: TM31 signal source for terminal DI/DO 10 / TM31 S_src DI/DO10
TM31 Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dyn. index: - Func. diagram: 9562
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0
p4041 BI: TM31 signal source for terminal DI/DO 11 / TM31 S_src DI/DO11
TM31 Can be changed: U, T Calculated: - Access level: 1
Data type: Unsigned32 / Binary Dyn. index: - Func. diagram: 9549, 9562
P-Group: Commands Units group: - Unit selection: -
Not for motor type: - Scaling: - Expert list: 1
Min Max Factory setting
- - 0