EasyManuals Logo

Cisco ONS 15454 Series User Manual

Cisco ONS 15454 Series
850 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #794 background imageLoading...
Page #794 background image
22-20
Cisco ONS 15454 Procedure Guide, R5.0
October 2005
Chapter 22 DLPs A500 to A599
DLP-A524 Download an Alarm Severity Profile
If the card is an FC_MR-4, E-Series Ethernet, G-Series Ethernet, OC-N, or electrical (DS-1,
DS-1N, DS-3, DS-3E, DS3i, DS3i-N, DS-3N, DS-3NE, DS3XM, or EC-1) card, click the
Provisioning > Alarm Profiles > Alarm Behavior tabs.
If the card is an ML-Series Ethernet (traffic) card, click the Provisioning > Ether Alarming >
Alarm Behavior tabs to apply the profile to the front physical ports, or the Provisioning >
POS Alarming > Alarm Behavior tabs to apply the profile to the POS ports. For more
information about ML-Series card ports and service, see the Ethernet Card Software Feature
and Configuration Guide for the Cisco ONS 15454 SDH, Cisco ONS 15454, and
Cisco ONS 15327.
b. Uncheck the Suppress Alarms check box for the port(s) you no longer want to suppress.
c. Click Apply.
Suppressed alarms will reappear in the Alarms window. (They might have previously been cleared from
the window using the Synchronize button.) The AS-CMD alarm with the port object (for example,
FAC-16-1) will be cleared in all views.
Step 4 Return to your originating procedure (NTP).
DLP-A524 Download an Alarm Severity Profile
Step 1 To access the alarm profile editor:
From network view, click the Provisioning > Alarm Profiles tabs.
From node view, click the Provisioning > Alarm Profiles > Alarm Profile Editor tabs.
From the card view of an FC_MR-4, E-Series Ethernet, G-Series Ethernet, OC-N, or electrical
(DS-1, DS-1N, DS-3, DS-3E, DS3i, DS3i-N, DS-3N, DS-3NE, DS3XM, or EC-1) card, click the
Provisioning > Alarm Profiles > Alarm Profile Editor tabs.
From the card view of an ML-Series Ethernet (traffic) card, click the Provisioning > Ether
Alarming > Alarm Behavior tabs to apply the profile to the front physical ports, or the
Provisioning > POS Alarming > Alarm Behavior tabs to apply the profile to the POS ports. For
more information about ML-Series card ports and service, see the Ethernet Card Software Feature
and Configuration Guide for the Cisco ONS 15454 SDH, Cisco ONS 15454, and Cisco ONS 15327.
Step 2 Click Load.
Step 3 If you want to download a profile that exists on the node, click From Node in the Load Profile(s)
dialog box.
a. Click the node name you are logged into in the Node Names list.
b. Click the name of the profile in the Profile Names list, such as Default.
Purpose This task downloads a custom alarm severity profile from a
network-drive-accessible CD-ROM, floppy disk, or hard disk location.
Tools/Equipment None
Prerequisite Procedures DLP-A60 Log into CTC, page 17-66
Required/As Needed As needed
Onsite/Remote Onsite or remote
Security Level Provisioning or higher

Table of Contents

Other manuals for Cisco ONS 15454 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco ONS 15454 Series and is the answer not in the manual?

Cisco ONS 15454 Series Specifications

General IconGeneral
Supported InterfacesEthernet
ManagementCisco Transport Controller (CTC), TL1, SNMP
Power Supply-48 VDC or AC (depending on power supply module)
Operating Temperature0 to 50°C (32 to 122°F) - varies by module
Storage Temperature-40°C to 70°C (-40 to 158°F)
Relative Humidity5 to 95%, noncondensing
Supported ProtocolsSONET/SDH, Ethernet, OTN
Platform TypeMulti-service transport platform

Related product manuals