Cisco ONS 15454 Series User Manual

Contents
xvi
Cisco ONS 15454 Procedure Guide, R5.0
December 2004
DLP- A356 TCC2/TCC2P Card Active/Standby Switch Test 20-40
DLP- A357 Create FC_MR-4 RMON Alarm Thresholds 20-41
DLP- A358 Delete FC_MR-4 RMON Alarm Thresholds 20-45
DLP- A359 Delete a Line DCC Termination 20-45
DLP- A362 Create a Four-Fiber BLSR Using the BLSR Wizard 20-46
DLP- A363 Create a Four-Fiber BLSR Manually 20-48
DLP- A364 Reset the TCC2/TCC2P Card Using CTC 20-49
DLP- A365 Initiate an Optical Protection Switch 20-50
DLP- A366 Initiate an Electrical Protection Switch 20-50
DLP- A367 Create a Provisionable Patchcord 20-51
DLP- A368 Delete a Provisionable Patchcord 20-52
DLP- A369 Provision an OC-N Circuit Route 20-53
DLP- A371 Remove Pass-through Connections 20-55
DLP- A372 Delete a Node from a Specified Login Node Group 20-56
DLP- A373 Install a MiniBNC EIA 20-57
DLP- A374 Change a Section DCC Termination 20-60
DLP- A375 Change a Line DCC Termination 20-60
DLP- A377 Provision Section DCC Terminations 20-61
DLP- A378 Provision Line DCC Terminations 20-62
DLP- A380 Provision a Proxy Tunnel 20-63
DLP- A381 Provision a Firewall Tunnel 20-64
DLP- A382 Delete a Proxy Tunnel 20-64
DLP- A383 Delete a Firewall Tunnel 20-65
DLP- A384 Add a Member to a VCAT Circuit 20-65
DLP- A385 Delete a Member from a VCAT Circuit 20-69
DLP- A386 Install Electrical Cables on the UBIC-V EIAs 20-70
DLP- A387 Change Line and Threshold Settings for the DS3XM-12 Card 20-74
DLP- A388 Change Line and Threshold Settings for the DS3/EC1-48 Cards 20-80
DLP- A390 View Alarms 20-85
DLP- A391 View CE-Series Ether Ports and POS Ports Statistics PM Parameters 20-87
DLP- A392 View CE-Series Ether Ports and POS Ports Utilization PM Parameters 20-88
DLP- A393 View CE-Series Ether Ports and POS Ports History PM Parameters 20-90
DLP- A394 View DS-N/SONET PM Parameters for the DS3XM-12 Card 20-91
DLP- A395 View BFDL PM Parameters for the DS3XM-12 Card 20-93
DLP- A397 Manually Route a Path Protection Circuit for a Topology Upgrade 20-95
DLP- A398 Automatically Route a Path Protection Circuit for a Topology Upgrade 20-95
DLP- A399 Install a UBIC-H EIA 20-97
CHAPTER 21 DLPs A400 to A499 21-1
DLP- A412 Install the DCU Shelf Assembly 21-1

Cisco ONS 15454 Series Specifications

General

Supported Interfaces	Ethernet
Management	Cisco Transport Controller (CTC), TL1, SNMP
Power Supply	-48 VDC or AC (depending on power supply module)
Operating Temperature	0 to 50°C (32 to 122°F) - varies by module
Storage Temperature	-40°C to 70°C (-40 to 158°F)
Relative Humidity	5 to 95%, noncondensing
Supported Protocols	SONET/SDH, Ethernet, OTN
Platform Type	Multi-service transport platform