INDEX
PagePage
C
(CALC) Key 2-34
Calculating Coordinate Values 2-305
Calculating Offset Data 2-301
Calculating the Coordinate Values to be
Specified in a Program 2-321
(CAN) Key 2-34
Cancel Mode 2-278, 2-335
Canceling Cutter Radius Offset Mode 2-187
Canceling Cutter Radius Offset Mode
(Compatible Specifications with Seicos) 2-187
CARD DNC OPERATION
(FROM USER MEMORY AREA) 2-91
CAUTION LABELS P-5
Cautions for Creating a Program 1-92
Cautions on Programming Tapping Using G32 2-146
Cautions on Programming Using G84 and G88 2-424
Cautions on the G76 Multiple Thread
Cutting Cycle 2-372
Cautions ON Using the G71 2-357
Cautions ON Using the G72 2-357
Cautions ON Using the G73 2-357
C-axis jog feed operation 2-19
C-axis rapid traverse operation 2-20
C-axis Zero Return Operation 1-15
Center-Work Programming 1-88
CF card 2-2
Change of Status 2-462
Changing Tool Number 2-461
Check for turret interference 1-100
Check Items after Executing Test Cutting 1-110
Check Items before Executing Test Cutting 1-109
Check Items before Starting Mass Production 1-117
CHECKING DIAGRAMS 1-8
Checking Lubricating Unit Operation 2-623
Checking Oil Level/Replenishing Oil 2-539
Checking Pressure Gage 2-541
Checking Set Positions 2-497
Checking the Operation of the Digital Tailstock 1-66
Checking the Program Using
the [Program Check] Button 1-99
Checking the Program
with the Coordinate System Shifted 1-104
Chip Conveyor (Option) 2-600
Chip Conveyor Buttons
(Chip Conveyor Specification) 2-26
CHUCK 1 CLAMP DIRECTION 2-66
CHUCK 1 FOOT SWITCH 2-66
CHUCK 1 FOOT SWITCH AT DOOR CLOSE 2-66
CHUCK 1 STROKE END CONFIRMATION
SWITCH 2-66
Chuck 1 Stroke End Detection Switch 2-69
Chuck Clamp Direction 2-68
Chuck Footswitch 1-48, 2-68
Chuck Footswitch with the Door Close 2-68
Chuck Jaw Stroke End Detection Function 2-69
CHUCKING 1-47
Chuck-Work Programming 1-86
Circular Arc Cutting 2-108
Clamping/Unclamping Chuck 1-48
Cleaning Air Filter and Condenser 2-578, 2-582
Cleaning Chip Conveyor 2-601
Cleaning Coolant Tank and Filter
(Chip Conveyor Rear Discharge Specifications) 2-535
Cleaning Coolant Tank and Filter
(Chip Conveyor Right Side Discharge
Specifications) 2-533
Cleaning Electrical Cabinet Fan 2-592
Cleaning Inside Machine 2-524
Cleaning Line Filter 2-563
Cleaning Lubricant Tank,
Suction Filter and Fill Port Filter 2-564
Cleaning Radiator 2-541
Cleaning Spindle Drain Hole 2-524
Cleaning Suction Strainer and Tank 2-542
Cleaning the Chuck 2-526
Clearing All Data 2-510
Clearing range (tool wear offset) 2-55
Closing Electrical Cabinet Door
with Main Power OFF 2-596, 2-598
Closing Electrical Cabinet Door
with Main Power ON 2-597, 2-599
Communication Parameter Screen 2-78
COMPATIBLE SPECIFICATIONS
WITH SEICOS (OPTION) 2-179
Compulsory Determination of Offset Direction 2-184
Compulsory Determination of Offset Direction
(Compatible Specifications with Seicos) 2-184
To Next Page
Loading...
Need help?
General
